# Fileset

[SusEneFuel(2026).pdf](https://mdr.nims.go.jp/filesets/6ba4b223-949d-47c1-bc33-1938c5dc1b5d/download)

## Creator

Preethi Perianayagam, Edwin Osebe Nyangau, Futa Imaizumi, [Naoka Nagamura](https://orcid.org/0000-0002-7697-8983), Hideharu Niwa, Takashi Itoh, Masaru Watanabe, Yuta Nakayasu

## Rights

[Creative Commons BY Attribution 4.0 International](https://creativecommons.org/licenses/by/4.0/)

## Other metadata

[Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes](https://mdr.nims.go.jp/datasets/07281d61-d229-4a0d-bafb-41880d267324)

## Fulltext

Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes  Sustainable Energy \& Fuels PAPER Published on 15 September 2026 Licensed under CC-BY 4.0Hydrothermally paA Research Center of Supercritical Fluid Tec Tohoku University, 6-6-11, Aoba, Aza, Aram Japan bCenter for Basic Research on Materials, Nat Sakura, Tsukuba, Ibaraki 305-0003, Japan cGraduate School of Advanced Engineering, T Katsushika, Tokyo, 125-8585, Japan dInstitute of Pure and Applied Sciences, Depa 1-1-1 Tennodai, Tsukuba, Ibaraki, 305-8571 eTsukuba Research Center for Energy Ma Tsukuba, 1-1-1 Tennodai, Tsukuba, Ibaraki, fFrontier Research Institute for Interdisciplina Aza, Aramaki, Aoba-ku, Sendai, Miyagi 980-85 Cite this: Sustainable Energy Fuels, 2026, 10, 4881 Received 7th July 2026 Accepted 14th September 2026 DOI: 10.1039/d6se00774k rsc.li/sustainable-energy This journal is © The Royal Society oreorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes Preethi Perianayagam, a Edwin Osebe Nyangau, a Futa Imaizumi,a Naoka Nagamura,bc Hideharu Niwa, de Takashi Itoh,f Masaru Watanabea and Yuta Nakayasu \*af Fe-assisted graphitization offers a route to convert renewable biomass into graphite, but high crystallinity and fast electrochemical kinetics are difficult to achieve simultaneously at reduced temperature. Here, we show that a short hydrothermal carbonization step can function as precursor architecture engineering rather than simple wet pretreatment. Fe(NO3)3-impregnated Japanese cedarwood was hydrothermally treated for only 15 min at 250 °C to generate an iron–carbon hydrochar precursor in which mixed iron oxide domains, including Fe3O4, are embedded within a reactive carbon matrix. During annealing at 1000 °C, these reducible iron oxide domains are converted into Fe/Fe3C catalytic interfaces that promote graphitic layer growth. After acid washing and mild air oxidation, the product exhibits graphite-like stacking with d002 z 0.3369 nm, low Raman disorder (ID/IG = 0.14), and a Raman-derived in-plane domain size of ca. 135 nm. HRTEM and SAED further revealed extended graphitic fringes and local single-crystal-like graphite domains within a polycrystalline sheet network. As a lithium-ion battery anode, the material, used without a post-synthetic surface coating, delivers 341/317 mAh g−1 lithiation/ delithiation capacities at 1C and exhibits reproducible lithiation behavior within each rate step up to 10C. These results identify hydrothermally preorganized iron–carbon precursors as an effective design principle for low-temperature biomass graphitization and high-rate lithium-ion storage.Introduction Graphite has long attracted interest from both academic and industrial communities because of its exceptional thermal stability, electrical conductivity, chemical resistance, mechan- ical robustness, andmachinability.1 These combined properties underpin its broad use in scientic and industrial applications. Among them, graphite is particularly important as the domi- nant anode material for lithium-ion batteries (LIBs), which are central to portable electronics, electric vehicles (EVs), and large- scale energy storage systems (ESS).2,3 Graphite remains thehnology, Graduate School of Engineering, aki, Aoba-ku, Sendai, Miyagi 980-8579, ional Institute for Materials Science, 3-13 okyo University of Science, 6-3-1, Niijuku, rtment of Physics, University of Tsukuba, , Japan terials Science (TREMS), University of 305-8571, Japan ry Sciences, Tohoku University, 6-3 Aoba, 78, Japan. E-mail: nakayasu@tohoku.ac.jp f Chemistry 2026preferred anode because it offers a theoretical capacity of 372 mAh g−1, a low operating potential of ∼0.1 V versus Li/Li+, high coulombic efficiency, and long cycle life.4,5 As demand for advanced batteries continues to grow, establishing a more secure and sustainable graphite supply has become a critical materials challenge. At present, both natural graphite (NG) and synthetic graphite (SG) are widely used as anode active materials. However, NG supply is vulnerable because mining capacity is geographically concentrated and expands slowly. SG therefore remains attrac- tive because it offers higher purity, more consistent properties, and greater exibility in precursor and microstructural design.2 Conventional SG production, however, is highly energy inten- sive. Established graphitization technologies, such as the Acheson process, can require temperatures approaching 3000 ° C, energy consumption of 5.5–12 MWh per ton of graphite, and batch production cycles of 13–16 days.6,7 Large thermal losses further reduce energy efficiency and increase cost.7 Even so- carbon precursors such as petroleum coke or coal tar pitch oen require severe conditions to achieve high graphitic ordering. These conditions also favor centralized infrastructure, which is not always well-suited to biomass feedstocks that are geographically distributed, heterogeneous, and oen handled in a wet state. For such feedstocks, practical implementationSustainable Energy Fuels, 2026, 10, 4881–4898 \| 4881[http://crossmark.crossref.org/dialog/?doi=10.1039/d6se00774k\&domain=pdf\&date\_stamp=2026-10-10](http://crossmark.crossref.org/dialog/?doi=10.1039/d6se00774k&domain=pdf&date_stamp=2026-10-10)[http://orcid.org/0009-0003-1724-0449](http://orcid.org/0009-0003-1724-0449)[http://orcid.org/0000-0002-9396-5156](http://orcid.org/0000-0002-9396-5156)[http://orcid.org/0000-0002-1009-7198](http://orcid.org/0000-0002-1009-7198)[http://orcid.org/0000-0003-2744-099X](http://orcid.org/0000-0003-2744-099X)[https://creativecommons.org/licenses/by/4.0/](https://creativecommons.org/licenses/by/4.0/)Sustainable Energy \& Fuels Paperbenets from process congurations that minimize pre- processing requirements, reduce the need for dedicated drying capacity, and remain compatible with exible or decentralized operation. Lower-temperature and shorter-duration graphitiza- tion routes are therefore attractive not only for reducing thermal demand but also for enabling more adaptable biomass-to- carbon processing in line with broader sustainability and net- zero goals.8 Among the proposed alternatives, catalytic graphitization has emerged as a promising strategy because it can induce graphitic ordering at substantially lower temperatures than conventional non-catalytic processes.9 Iron is especially attrac- tive owing to its low cost, abundance, and strong catalytic activity. In Fe-catalyzed graphitization, disordered carbon dissolves into iron-containing particles at elevated temperature and precipitates as ordered graphitic carbon aer saturation, following a dissolution–precipitation mechanism.10–12 For lignocellulosic precursors, however, the extent of graphitization depends strongly on the contact between catalytic species and the carbon matrix. Uniform dispersion of Fe within the precursor is therefore essential for producing highly crystalline graphite at reduced temperature.13 This makes precursor engineering particularly important. Liquid-phase impregnation with aqueous Fe(NO3)3 is a practical route to introduce Fe species into biomass before heat treat- ment.14 Oxygen-containing functional groups in wood can coordinate Fe during impregnation, improving catalyst distri- bution within the lignocellulosic framework.15,16 Upon heating under an inert atmosphere, these precursor species are con- verted into catalytically active iron-containing particles that mediate the transformation of amorphous carbon into graphitic domains.11,12 In this context, hydrothermal carbon- ization (HTC) provides an attractive platform for precursor design and conditioning. Because HTC uses water as the reac- tion medium, it can directly process wet biomass without energy-intensive drying and convert lignocellulosic feedstocks into carbonaceous intermediates under relatively mild conditions.12,17–21 Moreover, when combined with the intro- duction of aqueous Fe, HTC can facilitate the incorporation and redistribution of metal species within the precursor, thereby creating favorable conditions for subsequent catalytic graphi- tization. These features are particularly advantageous for distributed biomass resources, for which simplied front-end handling and tolerance to variable moisture content are important for practical implementation.13 Previous studies have demonstrated that biomass-derived graphite can be prepared via catalyst-assisted routes at lower temperatures than those used in traditional graphitization. For example, lignocellulose-derived carbon has been converted into articial graphite at 1500 °C with reversible capacities up to 340 mAh g−1,22 while hardwood biochar has been transformed into high-quality bio-graphite at 1200 °C using Fe catalysts, pre- heating, and slow cooling.23 Other catalyst-assisted systems based on saccharides likewise conrm the feasibility of producing highly crystalline graphite and promising LIB anodes from renewable precursors.24 Nevertheless, many reported routes still rely on annealing at ∼1200–1500 °C together with4882 \| Sustainable Energy Fuels, 2026, 10, 4881–4898tightly controlled thermal proles, which, although industrially accessible, increase thermal losses at these high temperatures, reduce design margins for furnace linings and heating elements, and make temperature uniformity across large batches more difficult to maintain, thereby limiting throughput and practical scalability.24–26 To address these scalability challenges using a widely avail- able regional feedstock, Japanese cedarwood (Cryptomeria japonica) was selected as the biomass precursor because it is a major and widely distributed plantation resource in Japan. Japanese Forestry Agency data indicate that planted forests cover approximately 10.09 million hectares and that Japanese cedar and cypress together account for approximately 70% of Japan's planted-forest area; many postwar Japanese cedar plantations have also reached an age suitable for harvesting and utilization.27 Japanese cedar is a representative lignocellulosic material comprising cellulose, hemicellulose, and lignin, and its cell-wall organization varies between earlywood and latewood.28,29 Previous studies of Japanese cedar and related Japanese conifer wood have shown that iron impregnation can modify char yield, surface area, and carbon structure during pyrolysis.30,31 These characteristics make Japanese cedar a relevant and locally avail- able model precursor for investigating the coupling of biomass architecture, iron chemistry, and catalytic graphitization. The selection of Japanese cedar does not, however, imply that the proposed process is limited to this species or that it is universally superior to other lignocellulosic feedstocks. The central challenge is therefore not only to lower the graphitization temperature, but also to design a biomass- derived precursor in which catalytic iron species and reactive carbon are positioned at short length scales before high- temperature treatment. We address this challenge by using a short hydrothermal carbonization step as a precursor- architecture tool. In the present process, Fe-impregnated Japa- nese cedarwood (CJ) is converted within 15 min into an iron– carbon hydrochar containing reducible mixed iron oxide domains, including Fe3O4. These domains are not regarded as the nal active catalyst themselves; rather, they provide a spatially preorganized reservoir of iron that is converted during 1000 °C annealing into Fe/Fe3C catalytic interfaces. This precursor architecture promotes the formation of highly ordered graphite, including local single-crystal-like graphitic domains. This highly crystalline development is corroborated by recent X-ray diffraction and structural analyses of cellulose- derived biocarbons, which conrm that metal catalysts effi- ciently drive the phase transformation of amorphous and tur- bostratic carbon into medium to long-range ordered graphitic structures.32 The resulting material exhibits reproducible high- rate lithiation behavior as a lithium-ion battery anode. The study thus links hydrothermal precursor chemistry, low- temperature catalytic graphitization, and electrochemical rate performance in a single biomass-to-graphite strategy. Results and discussion The process begins with a primary HTC step at 250 °C for different reaction times, enabling Fe incorporation within theThis journal is © The Royal Society of Chemistry 2026Fig. 1 Schematic representation of the experimental procedure carried out in this study. Paper Sustainable Energy \& Fuelswood-derived structure. Subsequent graphitization at 1000 °C under N2 ow promotes the formation of graphitic domains. A nal air calcination step at 400 °C selectively removes residual defect-rich or amorphous carbon, as illustrated in Fig. 1.Rapid generation of a hydrothermally preorganized iron– carbon precursor The X-ray diffraction (XRD) patterns of samples synthesized at 250 °C for durations ranging from 15 min to 4 h show principal reections consistent with a spinel-like Fe3O4 phase. The diffraction peaks align well with the characteristic inverse spinel structure of magnetite, with the most intense reection at ∼35.4° corresponding to the (311) plane, along with addi- tional peaks indexed to the (220), (400), (511), and (440) planes as shown in Fig. 2a. These peak positions and relative intensi- ties are consistent with previously reported hydrothermal synthesis of magnetite-based carbon composites at slightly lower temperatures (230 °C). This similarity suggests that magnetite formation is favored under the present hydrothermal conditions.33 The XRD patterns show minimal variation across different residence times, indicating that magnetite crystallization occurs rapidly under these conditions and reaches a structural plateau within 15 min. While the phase appears stable within the investigated time window, magnetite is known to be susceptible to oxidation under hydrothermal conditions. For example, partial transformation to hematite (Fe2O3) has beenThis journal is © The Royal Society of Chemistry 2026reported at elevated temperatures. In the present data, no unambiguous reections attributable solely to a-Fe2O3 were resolved by XRD. This may reect peak overlap, limited crys- tallite size, or insufficient long-range ordering and does not exclude a substantial hematite-like contribution. As discussed below, Fe K-edge XANES linear-combination tting indicates mixed Fe3O4- and a-Fe2O3-like environments.33 Importantly, the formation of Fe3O4 at this early stage plays a critical role in the subsequent graphitization behavior.34 Although Fe3O4 itself is not the most active catalytic phase, it serves as a precursor to catalytically active iron species during high-temperature treatment. Upon carbonization at 1000 °C, Fe3O4 can undergo reduction and restructuring to form tran- sient metallic iron or iron carbide species, which facilitate the reorganization of disordered carbon into ordered sp2-bonded graphitic domains.35–37 This catalytic transformation is reected in the thermogra- vimetric behavior. Thermogravimetric analysis (TGA) of the hydrochar precursors under an air atmosphere shows clear residence-time-dependent decomposition, where the 15 min sample exhibits signicant weight loss at 300–400 °C, likely due to the presence of reactive intermediates and residual volatile species from incomplete biomass decomposition, as shown in Fig. 2b.38 Longer residence times result in more stabilized hydrochar with reduced low-temperature decomposition. Aer Fe-catalyzed carbonization at 1000 °C, all bio-graphite (BGC) samples exhibit nearly identical oxidative TGA proles, char- acterized by a sharp, single-stage combustion peak betweenSustainable Energy Fuels, 2026, 10, 4881–4898 \| 4883Fig. 2 XRD pattern of (a) hydrochar synthesized at 250 °C with varying residence time. Thermogravimetric (TG/DTG) analysis of (b) hydrochar and (c) BGC revealing progressive thermal stabilization, (d) XRD pattern and (e) Raman spectra of bio-graphitic carbon synthesized at 250 °C with varying residence time followed by 1000 °C graphitization. Sustainable Energy \& Fuels Paper∼650 and 720 °C. This behavior is consistent with the combustion of ordered graphitic carbon structures formed through catalytic restructuring, as shown in Fig. 2c.26 The convergence of these oxidation proles indicates the formation of a structurally uniform and thermally stable graphitic carbon matrix, irrespective of the initial differences in hydrochar composition. This transformation is enabled by the catalytic activity derived from Fe3O4, which reduces the inu- ence of precursor-dependent heterogeneity during high- temperature treatment. The nal plateau observed near 800 ° C corresponds to the inorganic mineral ash content inherent to the original biomass feedstock, which remains consistent across all samples aer complete combustion.25,38 Conse- quently, even a short HTC residence time of 15 min is sufficient to produce a precursor capable of converting into high-quality graphitic carbon, highlighting the efficiency of the process.Residence-time control of low-temperature graphitic ordering Since this process depends strongly on the formation and activity of Fe species, hydrothermal residence time plays a crit- ical role in determining the extent of graphitization. Therefore, the inuence of hydrothermal residence time on graphitization was evaluated by XRD and Raman spectroscopy (Fig. 2d and e). Crystallite sizes were estimated from XRD data using the Scherrer equation. At the same time, Raman spectroscopy provided complementary information on defect density and graphitic domain development, derived from integrated peak areas (see SI for details). The structural parameters of each sample are summarized in Table 1.4884 \| Sustainable Energy Fuels, 2026, 10, 4881–4898To elucidate the role of the hydrothermal precursor archi- tecture, a control sample was prepared by directly calcining Japanese cedarwood impregnated with aqueous Fe(NO3)3 at 1000 °C without the hydrothermal carbonization step (denoted as No HTC). The XRD pattern of the No HTC sample exhibits only a broad, low-intensity feature near 26°, which is charac- teristic of highly amorphous carbon with negligible layer stacking. This indicates that the hydrothermal pre-treatment is essential to closely embed and activate the precursor iron species within the matrix to initiate subsequent graphitic ordering. Notably, implementing a short HTC duration of only 15 min already produces a sharp, highly discernible (002) reection. This rapid structural evolution yields a well-ordered domain with a crystal height Lc of approximately 46 nm, a lateral crystallite size La of approximately 69 nm, and an interlayer spacing (d002) of 0.3369 nm, demonstrating that effi- cient catalytic graphitic stacking can be successfully activated even with minimal hydrothermal residence times. Increasing the residence time to 1 h further enhances graphitic ordering, yielding the sharpest and most intense (002) peak (Lc z 49 nm, La z 68 nm, and d002 z 0.3368 nm), indi- cating optimal crystallite growth. However, extending the treat- ment to 2 h and 4 h leads to structural deterioration, as evidenced by peak broadening, reduced intensity, and decreased crystallite sizes (Lc: 44 / 35 nm; La: 67 / 49 nm). This degradation is attributed to structural collapse, excessive carbon consumption, and possible deactivation or agglomeration of Fe catalytic sites under prolonged hydrothermal conditions. Raman spectra for all samples show characteristic D (∼1350 cm−1), G (∼1580 cm−1), and 2D (∼2700 cm−1) bands,This journal is © The Royal Society of Chemistry 2026Table 1 Quantitative evaluation of crystallinity and disorder in bio-graphitic carbon via XRD and Raman spectroscopy Sample name XRD data (Scherrer equation) Raman spectroscopy data (Tuinstra–Koenig relation) FWHM (°) Crystallite thickness, Lc (nm) Lateral crystallite size, La, XRD (nm) Interlayer spacing, d002 (nm) ID/IG Raman-derived lateral crystallite size, La (nm) 15 m\_250\_3D 0.1799 45.98 69.14 0.3369 0.18 107.59 1 h\_250\_3D 0.1699 48.69 67.8 0.3368 0.14 133.77 2 h\_250\_3D 0.1860 44.48 66.64 0.3366 0.23 82.88 4 h\_250\_3D 0.2376 34.82 48.74 0.336 0.27 71.65 MCMB 0.1411 58.62 124.63 0.337 0.17 114.58 Articial graphite (coco peat) 0\.3227 25.63 65.92 0.3377 0.44 43.51 Paper Sustainable Energy \& Fuelsconrming the formation of graphitic carbon. Notably, even the 15 min sample already exhibits a clear 2D band, indicating that early-stage graphitic stacking is consistent with XRD results. The 2D band is widely recognized as a sensitive probe of graphitic stacking order, capable of distinguishing turbostratic carbon from well-ordered graphite through its shape and evolution.39 Quantitatively, the (ID/IG) ratio decreases from 0.18 for the 15 min sample to 0.14 for the 1 h sample, accompanied by an increase in Raman-derived La from ∼108 to ∼134 nm, indicating reduced defect density and growth of graphitic domains. In contrast, longer residence times (2–4 h) result in increased ID/IG (0.23–0.27) and decreased Raman-derived La (∼83–72 nm), reecting increased disorder. These trends are consistent with XRD patterns and conrm that excessive HTC leads to structural degradation. These results demonstrate that short HTC dura- tions (15 min–1 h) are sufficient to achieve substantial graphitic ordering (Lc z 46–49 nm, d002 z 0.3368–0.3369 nm) while avoiding degradation at longer times. From both structural and process perspectives, short-duration HTC provides a short- residence-time route for producing highly ordered biomass- derived graphitic carbon under the conditions investigated. The persistence of the D band indicates that defects are inherent to biomass-derived carbon systems, although their concentration is minimized at the optimal residence time of 1 h. These results are consistent with previous reports showing that excessive hydrothermal treatment can lead to structural degradation, highlighting the importance of optimizing resi- dence time.40 Thus, the 1 h condition gives the highest crystallinity, whereas the 15 min condition provides a process-relevant balance between short processing time and high graphitic ordering.How precursor architecture promotes graphitization at 1000 ° C Iron-catalyzed graphitization of biomass is generally described as a high-temperature process in which iron precursors are trans- formed during pyrolysis into catalytically active Fe and/or Fe3C particles that promote carbon ordering through dissolution– reprecipitation and carbide-mediated pathways. For example, Fe(NO3)3-impregnated lignocellulosic biomass has been reported to yield graphitic carbon via thermal decomposition of the ironThis journal is © The Royal Society of Chemistry 2026salt, followed by carbothermal reduction and in situ Fe3C formation.41 More generally, iron-catalyzed graphitization is considered to proceed through the formation of iron oxide nanoparticles and their subsequent conversion into Fe and/or Fe3C during high-temperature treatment.42–44 In these conven- tional systems, however, the catalytically active phases aremainly generated during pyrolysis itself. Building on our previous observation that the crystallite height (Lc) of graphitic carbon increases with Fe3O4 crystallite size in hydrothermally prepared precursors, hydrothermally formed Fe3O4 is regarded as a spatially preorganized and chemically pre-reduced precursor embedded within the hydro- char matrix.34 Under hydrothermal conditions, oxygen- containing functional groups derived from biomass interme- diates can coordinate Fe species, while reducing organic compounds generated from polysaccharide and lignin degra- dation partially reduce Fe(III) to Fe(II), thereby creating a mixed Fe(II)/Fe(III) redox environment favorable for magnetite forma- tion. This process can be schematically represented as follows: Fe3+ + xH2O # Fe(OH)x3−x + xH+ The hydrolyzed iron species then bind to the oxygen- containing functional groups (X = O or COO) on the biomass surface: (3 − x)Biomass − XH + \[Fe(OH)x\] (3−x)+ / \[Fe(biomass − X)3−x(OH)x\] + (3 − x)H+ R–CHO + 2Fe3+ + H2O / R–COOH + 2Fe2+ + 2H+ followed by magnetite crystallization: Fe2+ + 2Fe3+ + 4H2O / Fe3O4 + 8H+ or, under local hydrolysis/precipitation conditions, Fe2+ + 2Fe3+ + 8OH− / Fe3O4 + 4H2O Such behavior is consistent with previous reports on hydro- thermally prepared Fe3O4/carbon composites, where biomass-Sustainable Energy Fuels, 2026, 10, 4881–4898 \| 4885Sustainable Energy \& Fuels Paperderived organics act simultaneously as reducing agents and carbon sources, stabilizing Fe3O4 particles.45–47 Importantly, Fe2O3 could also serve as a reducible iron oxide precursor because hematite can be converted into metallic Fe through the sequential reduction pathway a-Fe2O3 / Fe3O4 / FeO / Fe under carbothermal conditions.48,49 However, in the present hydrothermal system, Fe3O4 is particularly signicant because its formation before annealing indicates that partial reduction of Fe(III) to Fe(II) and crystallization of a mixed-valence iron oxide have already occurred within the hydrochar matrix. This assignment is supported not only by XRD analysis but also by Fe K-edge XAFS characterization of the hydrothermally treated samples. As shown in the XANES region (Fig. 3a), the absorption edge positions of all experimental samples (15 min to 4 h) exhibit a prominent blue-shi relative to themetallic Fe-foil and FeO ref. 50. Instead, the edges align closely with the higher valence Fe3O4 and a-Fe2O3 standards, indicating that metallic Fe0 and FeO are not dominant detectable components under the present measurement conditions; their complete absence cannot be established.51 The identical pre-edge features, the same absorption energies, and the overlapping main peak proles (Fig. 3a) qualitatively point to similar mixed-oxide environments across the investigated residence times. To esti- mate the relative contributions of the reference phases, linear combination tting (LCF) of the XANES spectra was conducted (Table S4). At the onset of the reaction (15 min), the sample comprises 46% Fe3O4 and 54% a-Fe2O3. Extending the reaction time to 1 h results in a minor oxidation event, marginally increasing the a-Fe2O3 content to 60%. For the 2 h and 4 h samples, the tted phase fractions remain approximately constant at 44% Fe3O4 and 56% a-Fe2O3.52 The limited time-dependent structural change is further supported by the Fourier-transformed (FT) k3-weighted EXAFS spectra (Fig. 3b). All experimental samples display nearlyFig. 3 Fe K-edge X-ray absorption spectra of the experimental sample reference materials: (a) normalized XANES spectra with the correspondin k3-weighted EXAFS spectra. 4886 \| Sustainable Energy Fuels, 2026, 10, 4881–4898identical radial distribution functions, indicating similar local Fe coordination environments across the investigated residence times. The rst peak located at approximately 1.4 Å (uncorrected for phase shi) corresponds to the rst-shell Fe–O scattering.50 The second intense feature at roughly 2.7 Å is attributed to the Fe–Fe scattering shells associated withmixed Fe3O4- and a-Fe2O3- like environments. No distinct metallic Fe–Fe scattering feature comparable to that of the Fe foil reference at approximately 2.2 Å was detected within the sensitivity of the present measurements. Together, the XANES, LCF, and EXAFS results show no substan- tial time-dependent structural change aer 15 min at 250 °C within the resolution of the present measurements.51 Upon subsequent annealing at 1000 °C under N2, the embedded Fe3O4 can be carbothermally reduced by the surrounding carbon to form catalytically active Fe and/or Fe3C species: Fe3O4 + C / 3FeO + CO FeO + C / Fe + CO or, overall, Fe3O4 + 4C / 3Fe + 4CO followed by phase-dependent iron carbide formation and decomposition: 3Fe + C # Fe3C Fe3C / 3Fe + C(graphitic) The resulting Fe/Fe3C particles can subsequently catalyze the rearrangement of amorphous carbon into ordered graphitic domains through a dissolution–reprecipitation process: Camorphous / Cdissolved˛Fe / Cgraphitics treated at 250 °C over various reaction times compared to standard g pre-edge region shown in the inset, and (b) Fourier-transformed (FT) This journal is © The Royal Society of Chemistry 2026Paper Sustainable Energy \& FuelsTherefore, the high crystallinity of the nal graphite-like carbon can be attributed to two sequential and inter- connected processes: rst, the hydrothermal formation of crystalline Fe3O4 within the hydrochar matrix, and second, the carbothermal conversion of this embedded Fe3O4 into active Fe/ Fe3C graphitization catalysts during annealing. The hydro- thermal step should be interpreted as a precursor-architecture process. Scanning electron microscopy (SEM) and energy- dispersive X-ray spectroscopy (EDS) were used to evaluate the morphology and elemental composition of the hydrochar (15 min to 4 h), as shown in Fig. S3–S7 (SI). The SEM micro- graphs reveal a highly irregular, rugged, and porous surface microstructure inherited from the lignocellulosic cellular walls of the cedar wood biomass. EDS elemental mapping shows that Fe signals are broadly distributed across the examined hydro- char regions, consistent with widespread incorporation of the iron precursor during the hydrothermal step. The phase iden- tity of the Fe-containing species is assigned from the combined XRD and XAFS results rather than from EDS alone. XRD conrms the rapid formation of crystalline iron oxide domains in the hydrochar, while Fe K-edge XAFS indicates that the iron phase is better described as a mixed iron oxide state rather than purely metallic iron or a single Fe3O4 phase. Thus, the mecha- nistic importance of the hydrothermal product lies not in Fe3O4 as an isolated active catalyst, but in the formation of reducible iron oxide domains intimately embedded within a reactive wood-derived carbon matrix.Selective structural renement by acid washing and mild air oxidation Aer catalytic graphitization under a nitrogen atmosphere and subsequent acid washing, a certain amount of defect-rich or amorphous carbon remained. Therefore, air calcination was conducted at 400 °C for 1 h to selectively remove residual defect- rich or amorphous carbon and enhance the relative graphitic ordering of the carbon material. X-ray diffraction (XRD) was used to track the structural evolution and crystallinity enhancement of the 15 m\_250\_3D carbon sample, as shown in Fig. 4a, from hydrochar to nal air-treated graphite, compared against reference graphite. The hydrochar displayed a broadFig. 4 XRD patterns (a) show phase evolution from hydrochar to Fe-assis of (002) peak profiles highlighting crystallinity differences between BGC, graphitic ordering transition in BGC compared with commercial graphit This journal is © The Royal Society of Chemistry 2026carbon-related feature around 26.5°, characteristic of low graphitic ordering, along with peaks corresponding to Fe3O4, indicating the formation of iron oxide species during HTC. In the “before HCl” sample, only a-Fe was detected near 45°, conrming the partial reduction of iron species, although complete removal had not yet occurred due to the absence of acid washing. Aer HCl washing, the (002) reection became more prominent, while no diffraction peaks attributable to crystalline Fe-containing phases were detected within the detection limit of XRD. This observation is consistent with the removal of XRD-detectable crystalline and exposed Fe- containing species but does not establish complete Fe removal. Subsequent air oxidation at 400 °C for 1 h intensied the graphitic reections and decreased the Raman ID/IG ratio, indicating selective removal of defect-rich or amorphous carbon. Because the XRD-derived Lc changed only slightly aer air calcination, this treatment is interpreted as a structural renement step that increases the relative fraction of ordered graphitic domains rather than inducing substantial additional crystal growth. These features closely resemble those of the reference articial graphite. The progressive sharpening of the (002) peak, together with the absence of XRD-detectable crystalline Fe-containing phases aer acid washing, supports the structural evolution of the acid- washed product toward highly ordered graphitic carbon. EDS analysis of selected regions showed only a weak Fe signal in BGC and post-air BGC (Table S6); however, because EDS is local and semi-quantitative, trace, amorphous, or highly dispersed residual Fe cannot be excluded without bulk elemental quan- tication, and its possible contribution to the observed prop- erties cannot be completely ruled out. The (100) and (101) reections further provide insight into the in-plane structural order. Although commercial MCMB shows sharp and intense diffraction peaks indicative of a highly ordered graphitic structure, articial graphite exhibits comparatively broader and less dened reections. Interestingly, both the BGC (before air calcination) and air-treated BGC samples present signicantly broadened features, characteristic of turbostratic or nano- crystalline carbon domains. Importantly, air calcination does not markedly inuence the position or prole of the in-plane reections, indicating that the underlying crystallineted bio-graphitic carbon before and after air calcination, (b) comparison artificial graphite, and MCMB (c) Raman spectra illustrating defect-to- ic carbons. Sustainable Energy Fuels, 2026, 10, 4881–4898 \| 4887Table 2 Raman- and XRD-derived structural parameters of 15 m\_250\_3D carbon before and after air calcination Sample ID/IG La (nm) Lc (nm) Before calcination 0.18 107.59 45.98 Aer calcination 0.14 134.52 44.86 Articial graphite (coco peat) 0.44 43.51 25.63 MCMB 0.17 114.58 58.62 Table 3 CHNSO elemental composition of CJ used as the biomass feedstock Samples Elements C (%) H (%) N (%) S (%) O (%) CJ 49.81 6.04 0.14 NIL 43.29 Sustainable Energy \& Fuels Paperframework remains intact, while predominantly removing surface-associated disorder as shown in Fig. 4b. Notably, a slight decrease in the crystallite height (Lc) from 45.98 nm to 44.86 nm was observed aer air calcination, which may be attributed to the mild oxidation-induced removal of amorphous carbon, resulting in a marginal reduction in stacking height without compromising the overall graphitic framework as shown in Table 2. Raman analysis further conrms this structural renement. The N2-carbonized 15 m\_250\_3D sample exhibits an ID/IG ratio of 0.18, corresponding to a Raman-derived in-plane crystallite size (La) of 107.6 nm. Aer air calcination, the ID/IG ratio decreases to 0.14, accompanied by an increase in La to 134.5 nm, indicating a clear reduction in defect density and an increased relative fraction of ordered graphitic domains. Interestingly, the air-treated sample achieves a Raman-derived La comparable to that of the optimized 1 h sample (see Table S3), suggesting that mild oxidative treatment can partly compensate for shorter hydrothermal residence times by removing defect-rich carbon. This behavior is consistent with established studies showing that selective oxidation removes disordered or amorphous carbon phases, thereby enhancing the relative proportion of graphitic domains and improving overall crystallinity. Reductions in ID/IG ratios following oxida- tive treatment have been widely reported as evidence of microstructural renement in hybrid amorphous/graphitic carbon systems.53,54 Qualitatively, the Raman spectra show a suppression of the D-band intensity and a more symmetric and intense 2D band aer air treatment, consistent with a reduced relative contri- bution from defect-rich carbon and an increased contribution from graphitic domains. These observations are consistent with XRD results and further support the conclusion that air calci- nation acts as a structural renement step. Controlled oxidation is known to preferentially target loosely bound, amorphous, or defect-rich carbon regions, particularly at the surface, thereby preferentially removing reactive surface-associated carbon without producing a substantial change in the XRD-derived stacking thickness, as shown in Fig. 4c.55 However, the effec- tiveness of this approach depends critically on the severity of treatment, as excessive oxidation can lead to carbon loss and lattice etching.56 In this study, controlled air oxidation provides a practical structural-renement step under the conditions examined, although direct TEM/HRTEM and XPS comparisons would be required to resolve local lattice and surface-chemical changes.4888 \| Sustainable Energy Fuels, 2026, 10, 4881–4898Comparative SEM images obtained before and aer air treatment are shown in Fig. S8. Aer air treatment, the ne surface overlayer becomes less prominent and larger carbona- ceous domains are more clearly exposed. These images provide complementary evidence of an accompanying morphological change. However, SEM does not directly resolve local lattice ordering or surface chemical states; therefore, it is not used as direct evidence of crystallization. The interpretation of the air treatment is limited to preferential removal of reactive or disordered carbon and the resulting relative enrichment of graphitic domains inferred from the combined XRD and Raman results.Process-relevant short-time synthesis and preliminary scale- up To evaluate the process's carbon retention efficiency, elemental analysis (CHNSO) was conducted on the CJ (Table 3). The resulting carbon content was used to calculate the carbon yield of the biomass-derived graphitic carbon (BGC) obtained under the selected 15 min HTC and 1000 °C annealing conditions. The carbon yield was determined using the following equation: Carbon yield �w w % �  ¼ Mass of BGC Mass of SD�  Carbon content �  100 Here, an assumed carbon fraction of 0.99 was used to provide an approximate estimate of carbon retention in the nal graphitic carbon aer acid washing and air oxidation. The inuence of residence time on both hydrochar and carbon yield was systematically assessed. A gradual decline was observed in both metrics as the residence time increased: mass yield decreased from 0.80% at 15 min to 0.74% at 4 hours, while carbon yield fell from 1.60% to 1.47% as shown in Fig. 5a. These modest reductions indicate that prolonged HTC promotes additional volatilization and decomposition of thermally sensitive constituents, resulting in lower solid recovery. This trend is well-supported by literature, which shows that increasing residence time enhances biomass degradation through hydrolysis and subsequent reactions, shiing product distribution toward bio-oil and gaseous phases rather than solid hydrochar. Reactions such as decarboxylation and dehy- dration, which occur rapidly at early stages but continue with extended treatment, contribute to progressive carbon loss and reduced solid yield. Consequently, shorter residence times appear more effective for retaining both total mass and carbon, highlighting their suitability for energy-efficient hydrochar production.57This journal is © The Royal Society of Chemistry 2026Fig. 5 Mass yield and carbon yield of BGC as a function of (a) HTC residence time and (b) comparison of bench-scale and small-scale synthesis. Paper Sustainable Energy \& FuelsThis behavior is consistent with trends reported in previous studies. Ghanim et al. demonstrated that hydrochar yield generally decreases with increasing HTC severity, although xed carbon content and energy density tend to improve under such conditions.58 Similarly, Reza et al. observed reduced carbon recovery with increasing temperature and residence time, attributed to enhanced dissolution of organic and inor- ganic fractions into the process water.59 More broadly, it is widely recognized that while temperature is the dominant parameter governing HTC severity, residence time remains a critical factor controlling the extent of feedstock decomposi- tion and preservation of the carbon matrix.57 The observations in the present study, therefore, reinforce that HTC severity, whether controlled through time or temperature, plays a deci- sive role in governing hydrochar yield and carbon retention. To examine preliminary transferability beyond the original batch size, bench-scale experiments were conducted under the 15 min HTC condition using a reactor volume and biomass loading four times larger than those of the small-scale setup. The scaled 15 m\_250\_3D sample showed a substantial increase in both mass and carbon yield compared with the small-scale sample: mass yield more than doubled, from 0.80% to 1.96%, while carbon yield increased by approximately 2.5 times, from 1.60% to 3.93%, as shown in Fig. 5b. These results demonstrate that the process could be reproduced at a larger laboratory batch size under the tested conditions; however, they should not be interpreted as evidence of industrial scalability. The higher yield observed in the bench-scale experiment may reect differences in reactor geometry, heat-transfer history, liquid-to-solid contact, and material handling losses between the two scales. Accordingly, the difference in yield cannot be attributed solely to the fourfold increase in biomass loading or to the 15 min residence time. Because these factors can strongly affect HTC product recovery, further scale-up studies with controlled heat-transfer and mixing conditions are required to determine their relative contributions. It is well established that, although intrinsic reaction kinetics remain scale- independent, physical parameters such as heat transfer, mix- ing, and mass transport govern reactor performance andThis journal is © The Royal Society of Chemistry 2026product selectivity during scale-up.60,61 Poor control over these parameters can lead to temperature gradients and undesired side reactions, ultimately reducing yield, whereas improved transport conditions can help preserve the carbon matrix and enhance solid recovery.62,63 In contrast, the decreasing yields observed at longer resi- dence times suggest that extended HTC promotes volatilization and thermal degradation, ultimately lowering the amount of recoverable carbon. Thus, the high recovery obtained with the 15 min condition under the present conditions is consistent with reduced structural degradation, whereas the additional increase observed in the larger-scale experiment may be asso- ciated with scale-dependent differences in heat transfer, mix- ing, liquid–solid contact, and recovery efficiency. The results therefore support short-duration HTC as a favorable condition for bench-scale hydrochar production under the conditions investigated. Nevertheless, catalytic graphitization at industrially relevant scale will require addi- tional assessment of catalyst distribution, catalyst residue retention, catalyst recovery and reuse, heat and mass transfer, temperature uniformity, energy consumption, reactor throughput, and process economics. The present 10–40 g comparison should consequently be regarded as a preliminary laboratory-scale scale-up assessment rather than a demonstra- tion of commercial feasibility. Further experiments at progres- sively larger batch sizes or under continuous operation will be necessary to determine whether the observed yield and material-property trends are maintained when transport limi- tations and catalyst-management requirements become more signicant.60–63Local single-crystal-like graphitic domains in a polycrystalline sheet network The SEM images of BGC (15m\_250\_3D), shown in Fig. 6a, reveal a heterogeneous and highly aggregated morphology over the micrometer scale. At lower magnication, the carbon exhibits irregular aggregates containing larger lamellar and brous features together with ner fragmented structures. At higherSustainable Energy Fuels, 2026, 10, 4881–4898 \| 4889Fig. 6 Multiscale morphology and local graphitic ordering of BGC (15 m\_250\_3D): (a) SEM images obtained at low and high magnification; (b) TEM image showing crumpled sheet-like aggregates; (c) HRTEM image showing graphitic lattice fringes; (d) SAED pattern from a polycrystalline or textured graphitic region; and (e) SAED pattern showing discrete hexagonally arranged diffraction spots from a locally highly oriented graphitic region. Sustainable Energy \& Fuels Papermagnication, numerous wrinkled and ake-like carbon frag- ments are observed, suggesting substantial morphological reconstruction of the biomass-derived carbon during hydro- thermal treatment and subsequent Fe-assisted graphitization. The coexistence of larger carbonaceous structures and nely divided sheet-like fragments indicates a hierarchical morphology with considerable structural heterogeneity. These SEM observations provide the microscale morphological context for the crumpled and sheet-like structures observed by TEM. At the nanoscale, the transmission electron microscopy (TEM) analysis, as shown in Fig. 6b, reveals crumpled, sheet-like carbon structures forming loosely packed aggregates, which are characteristic of biomass-derived carbon materials.25,64 These irregular morphologies reect the preservation of structural templates during carbonization and are commonly observed in hydrothermally and thermally treated biomass chars, where complex, multi-scale architectures are formed.57,64 TEM images further indicate notable structural heterogeneity, with semi- transparent regions corresponding to thin, few-layer graphitic domains, while darker, opaque regions represent thicker, multilayer graphitic assemblies.55,65 The observed wrinkling and folding originate from the reconstruction processes during biomass decomposition and subsequent catalytic graphitiza- tion.56,65 Moreover, the interconnected and sheet-like morphology may facilitate electrolyte access and Li+ transport, contributing to the observed rate capability.57,66 This hierar- chical structural organization, consisting of both ordered and4890 \| Sustainable Energy Fuels, 2026, 10, 4881–4898disordered domains, conrms the effectiveness of the rapid Fe- assisted catalytic graphitization process in converting biomass into graphitic carbon.55,65 In Fig. 6c, high-resolution transmission electron microscopy (HRTEM) conrms that the nal BGC contains extended parallel lattice fringes with an interlayer spacing of approxi- mately 0.33–0.34 nm,25,66,67 consistent with graphite (002) stacking.56,65,66 In addition to polycrystalline ring-like SAED patterns, selected regions exhibit discrete diffraction spots arranged with hexagonal symmetry. These spots are assigned to in-plane graphite reections and indicate local single-crystal- like graphitic domains viewed close to the \[0001\] zone axis. The extended and continuous nature of these fringes indi- cates a high degree of graphitic stacking order, while slight distortions and curvature suggest the presence of defects or turbostratic stacking in certain regions.34,55,68 These observa- tions conrm the formation of graphitic carbon with a well- developed layered structure.22 In regions exhibiting polycrystalline characteristics, as shown in Fig. 6d, the selected area electron diffraction (SAED) pattern displays concentric diffraction rings with intensity modulation, indicating a polycrystalline graphitic structure with preferred orientation.34,55,69 The innermost diffuse ring is indexed to the (002) plane, corresponding to interlayer stacking of graphene layers, while the outer rings are assigned to the (100) and (110) planes, reecting in-plane crystallographic ordering.43,70 The presence of discontinuous arcs rather thanThis journal is © The Royal Society of Chemistry 2026Paper Sustainable Energy \& Fuelscontinuous rings further conrms a textured polycrystalline nature with partially aligned graphitic domains.55 In contrast, other regions exhibit single-crystal-like diffrac- tion features, as shown in Fig. 6e, where the SAED pattern shows well-dened, discrete diffraction spots arranged in a hexagonal symmetry, indicating locally highly ordered graphitic domains.66,69 The central transmitted beam corresponds to the (000) reection, while the surrounding diffraction spots are indexed to the (100) and (110) planes.45,71 The absence of diffraction rings and the presence of sharp, periodically arranged spots indicate locally highly ordered graphitic domains with single-crystal-like diffraction features, consistent with a \[0001\] zone axis orientation where the electron beam is aligned parallel to the c-axis.70,71 Conventional biochar derived from direct biomass pyrolysis typically retains a rigid, blocky framework, resulting in a dense and monolithic morphology.64 The Fe-assisted graphitization treatment substantially reconstructs the carbon architecture, resulting in a heterogeneous morphology comprising irregular aggregates, wrinkled/ake-like fragments, and locally sheet-like structures.72 This transformation yields a hybrid morphology consisting of both few-layer graphene-like sheets and thicker multilayer graphitic domains, forming a hierarchical and interconnected structure.25 Such structural evolution from a dense precursor to a sheet-like graphitic framework highlights the effectiveness of catalytic restructuring in reducing defect- rich carbon regions and enhancing graphitic ordering. The resulting material is structurally distinct from conventional biochar and provides a graphitic, sheet-like morphology suit- able for lithium-ion storage.High-rate discharge behavior of biomass-derived graphite without post-synthetic surface coating The rate capability of the BGC electrode was rst evaluated on the discharge/lithiation branch (Fig. 7a). In the graphitekLi half- cell conguration, discharge corresponds to Li+ intercalation into graphite, whereas charge corresponds to Li+ dein- tercalation. The lithiation capacity decreased progressively as the rate increased from 0.1C to 10C, consistent with increasing polarization and the reduced time available for Li+ transport at high current.73 Nevertheless, the capacity remained stable within each rate step, indicating reproducible operation of the BGC electrode under high-rate lithiation. The charge/delithiation branch exhibited a greater capacity loss at high rates (Fig. S11). This difference should be inter- preted as a protocol- and cell-dependent rate response rather than as evidence that Li+ deintercalation is intrinsically more difficult than intercalation in graphite. At high current, elec- trolyte, solid-state, charge-transfer, and ohmic overpotentials can cause the voltage cutoff to be reached before Li+ extraction is complete, particularly in a structurally heterogeneous porous electrode.74 For biomass-derived catalytically graphitized carbon, variations in crystallinity, turbostratic disorder, pore structure, surface chemistry, and interfacial resistance may further broaden the distribution of Li+ transport kinetics.75 Because the lithiation and delithiation measurements wereThis journal is © The Royal Society of Chemistry 2026performed in separate cells, cell-to-cell differences may also contribute to the observed asymmetry. Accordingly, BGC is best described as exhibiting favorable high-rate lithiation perfor- mance, while its fast-rate delithiation remains limited under the present test conditions. Further optimization of electrode density, particle-size distribution, surface chemistry, and interfacial resistance is required to improve high-rate delithiation. The electrochemical reversibility and early interfacial stabi- lization of the BGC electrode were further evaluated at 0.1C, as shown in Fig. 7b. The electrode exhibits an initial coulombic efficiency of approximately 93%, indicating limited irreversible Li consumption associated mainly with solid electrolyte inter- phase formation.25,73,76 The coulombic efficiency increases during the initial cycles and reaches approximately 95% by the h cycle. Although this value still requires improvement for practical full-cell operation, the rapid stabilization suggests that the graphitic framework forms a relatively stable electrode– electrolyte interface without post-synthetic surface coating. The discharge/lithiation capacity also remains relatively stable during the initial cycles, indicating that the electrode maintains its accessible Li-storage capacity during early cycling. These ve initial cycles are intended to evaluate the early electrochemical stabilization of the electrode and should not be interpreted as evidence of long-term cycling stability. The cyclic voltammetry curves for the rst three cycles are shown in Fig. 7c. The cathodic features correspond to lithiation, whereas the anodic features correspond to delithiation.21,24 The close overlap of the second and third cycles indicates good early-cycle reversibility aer initial SEI formation. This behavior is consistent with the formation of a stable graphitic host structure that can repeatedly accommodate Li insertion and extraction during the early cycles. The galvanostatic charge–discharge proles at 1C are shown in Fig. 7d. The rst cycle includes irreversible capacity associ- ated with SEI formation. In the second cycle, the lithiation and delithiation capacities are 341 and 317 mAh g−1, respectively, corresponding to a coulombic efficiency of approximately 93% when calculated as the delithiation capacity divided by the lithiation capacity. By the third cycle, the delithiation capacity stabilizes at approximately 315 mAh g−1, corresponding to about 85% of the theoretical capacity of graphite even at the accelerated 1C rate. The proles exhibit clear low-voltage plateaus below 0.5 V vs. Li/Li+, which are characteristic of staged Li+ intercalation into graphitic layers.22,24,67 The small cycle-to-cycle change in the voltage proles further supports stable early-cycle reversibility of the BGC electrode. The electrochemical performance of the BGC electrode is notable because the active material was used without any post- synthetic surface coating. In many graphite anode systems, carbonaceous coatings are introduced to passivate surface defects, suppress excessive electrolyte decomposition, and improve initial coulombic efficiency and cycling stability.66 In contrast, the present BGC delivers high 1C lithiation/ delithiation capacities and stable early-cycle behavior without such coating treatment. This indicates that the precursor- derived graphitic architecture, including low Raman disorder,Sustainable Energy Fuels, 2026, 10, 4881–4898 \| 4891Fig. 7 Electrochemical performance of the BGC (15 m\_250\_3D) electrode: (a) lithiation rate capability over five cycles at each C-rate; (b) initial- cycle lithiation capacity and coulombic efficiency at 0.1C; (c) cyclic voltammograms recorded at 0.1 mV s−1; and (d) galvanostatic lithiation/ delithiation profiles at 1C. Sustainable Energy \& Fuels Papergraphite-like stacking, and local single-crystal-like graphitic domains, contributes to the intrinsic electrochemical quality of the material. To place the electrochemical performance of the present BGC in context, Table 4 compares its synthesis conditions and lithium-storage behavior with representative biomass-derived graphitic anodes. Because graphite half-cells can show different lithiation/discharge and delithiation/charge responses at high C-rates, both branches are separated where the original reports provide sufficient information. When only reversible capacity is reported, the charge and discharge branches are not separated. This comparison indicates that the present BGC should be positioned as a process-advantaged biomass-derived graphite rather than as a record-capacity material. Some recent biomass- derived graphites reach higher absolute capacities when pro- cessed at higher graphitization temperatures or when modied by dopants or lattice engineering. For example, pyrolysis-bio-oil- derived biographite can approach the theoretical capacity of graphite aer graphitization at 1500 °C, and Nb-doped coffee- husk-derived biographite can deliver very high capacity through heteroatom/lattice engineering. In contrast, the present BGC, used without post-synthetic surface coating, delivers 341/317 mAh g−1 lithiation/delithiation capacities at 1C aer only a 15 min HTC precursor-organization step and4892 \| Sustainable Energy Fuels, 2026, 10, 4881–4898graphitization at 1000 °C. Thus, the advantage of the present material lies in the combination of low-temperature synthesis, short hydrothermal precursor organization, operation without post-synthetic surface coating, local single-crystal-like graphitic domains, and stable high-rate discharge/lithiation behavior. From a processing perspective, eliminating post-synthetic coating reduces material complexity and avoids additional coating precursors and thermal treatments.25,66 Therefore, the BGC developed in this study can be regarded as a process- advantaged graphite material that achieves promising lithium-ion storage performance through intrinsic structural quality rather than external surface modication. This result highlights the effectiveness of hydrothermal precursor archi- tecture engineering for producing highly crystalline biomass- derived graphite suitable for high-rate discharge applications. Because graphitization temperatures above 1000 °C were not systematically examined, 1000 °C should not be regarded as the fully optimized graphitization temperature. Rather, it is the lowest temperature evaluated in this study that produced graphite-like domains and promising electrochemical perfor- mance. Direct comparisons at 1200–1500 °C will be required to determine whether higher temperatures can further suppress the sloping capacity, improve graphitic ordering, and enhance lithiation/delithiation kinetics.This journal is © The Royal Society of Chemistry 2026T ab le 4 C o m p ar at iv e o ve rv ie w o f sy n th e si s co n d it io n s an d lit h iu m -i o n st o ra g e p e rf o rm an ce o f b io m as s- d e ri ve d g ra p h it ic an o d e s M at er ia l/ so ur ce Fe ed st oc k an d pr oc es s T m ax D is ch ar ge /l it h ia ti on be n ch m ar k C h ar ge /d el it h ia ti on or re ve rs ib le be n ch m ar k R at e/ cy cl in g n ot e T h is w or k Ja pa n es e ce da rw oo d; Fe (N O 3 ) 3 im pr eg n at io n ;H T C 25 0 °C , 15 m in ;N 2 an n ea li n g; H C l w as h in g; m il d ai r ox id at io n ;a ct iv e m at er ia l us ed w it h ou t po st - sy n th et ic su rf ac e co at in g 10 00 °C 34 1 m A h g− 1 li th ia ti on at 1C , 2n d cy cl e 31 7 m A h g− 1 de li th ia ti on at 1C ,2 n d cy cl e. C h ar ge / de li th ia ti on at h ig h C -r at e; ea rl y C E ca . 93 –9 5% D is ch ar ge /l it h ia ti on ra te br an ch re m ai n s co m pa ra ti ve ly st ab le up to 10 C w it h 30 cy cl es D ey et al ., En er gy Fu el s 20 25 (r ef .7 7\) Py ro ly si s bi o- oi l; lo w -t em pe ra tu re pr et re at m en t 15 0– 20 0 °C ; Fe \-c at al yz ed gr ap h it iz at io n 15 00 °C R ep or te d n ea rl y th eo re ti ca l sp ec i c ca pa ci ty ar ou n d 37 0 m A h g− 1 Se pa ra te ch ar ge /d is ch ar ge va lu es n ot av ai la bl e fr om ab st ra ct ;I C E 90 .0 3% M in im al fa di n g a er 50 cy cl es in LI B h al f- ce lls G ul as et al ., AC S O m eg a 20 26 (r ef .7 8\) In d us tr ia l bi om as s- d er iv ed sy n th et ic gr ap h it e; ca ta ly st -f re e A ch es on \-t yp e sy n th es is fr om w oo d/ fo re st ry re si du es In du st ri al gr ap h it iz at io n Li + di sc h ar ge at 0. 1C :3 31 .0 m A h g− 1 (B D SG B ), 33 5. 7 m A h g− 1 (B D SG D ) Fi rs t C E :8 8\. 3% (B D SG B ), 87 .2 % (B D SG D ). 2C ch ar gi n g vs . 0. 2C ch ar gi n g: 25 .0 % an d 26 .5 % 3C di sc h ar gi n g vs .0 .2 C di sc h ar gi n g: 59 .7 % an d 68 .6 % D ey et al ., G re en C he m . 20 24 (r ef .7 0\) H ar dw oo d- de ri ve d py ro ly si s oi l; re du ce d Fe po w de r; ac id w as h in g 15 00 °C Fi rs t/ se co n d di sc h ar ge –c h ar ge pr o le re po rt ed ;i n it ia l re ve rs ib le ca pa ci ty ab ou t 35 0 m A h g− 1 IC E 90 .2 % ;C E st ab il iz es n ea r 99 % a er in it ia l cy cl es R at e te st ed fr om 0\. 1C to 4C ; ca pa ci ty de cr ea se s w it h C -r at e an d re co ve rs w h en re tu rn ed to 0. 1C Je on g et al ., J. Al lo ys C om pd .2 02 5 (r ef .2 2\) Li gn oc el lu lo se + Fe ca ta ly st ; ca ta ly ti c gr ap h it iz at io n at 15 00 –2 50 0 °C 15 00 –2 50 0 °C L- A G -2 50 0 sh ow s ar ou n d 34 0 m A h g− 1 ;L \-A G -1 50 0 ar ou n d 30 0 m A h g− 1 N ot se pa ra te d in ab st ra ct ; de sc ri be d as re ve rs ib le ca pa ci ty St ab le ov er 10 0 cy cl es ;h ig h - ra te ca pa bi li ty up to 5C ,b ut ra te ca pa bi li ty de sc ri be d as in fe ri or an d n ee di n g im pr ov em en t W an g et al ., Su st ai na bl e En er gy Fu el s 20 25 (r ef .7 9\) W h ea t st ra w ,r ic e st ra w ,c or n st al ks ;K 2 C O 3 –N a 2 C O 3 m ol te n -s al t el ec tr ol ys is ;s il ic a re m ov al as si st s gr ap h it iz at io n 85 0 °C el ec tr ol ys is G ra ph it e an od e: 29 3 m A h g− 1 at 0\. 1 A g− 1 N ot se pa ra te d in ar ti cl e la n di n g pa ge C om m er ci al gr ap h it e co m pa ri so n :2 87 .8 m A h g− 1 at 0\. 1 A g− 1 T h om as et al ., M R S En er gy \& Su st ai na bi li ty 20 26 (r ef .8 0\) Fe -c at al yz ed ce llu lo se /d ex tr in / li gn in py ro ly si s 14 00 °C Fe \-c at al yz ed ce llu lo se :s ec on d- cy cl e di sc h ar ge ca pa ci ty 29 6 m A h g− 1 A ve ra ge re ve rs ib le ca pa ci ty 27 8 m A h g− 1 ov er  ve cy cl es ; IC E 77 .2 % fo r ce llu lo se C /8 h al f- ce ll pr ot oc ol ;f ul l-c el l ce llu lo se ca se re po rt ed 30 4 m A h g− 1 in it ia l ca pa ci ty an d 71 .6 % re te n ti on a er 70 cy cl es in th e be tt er ce ll Fl at C he m 20 25 co ff ee - gr ou n d bi o- gr ap h it e8 1 W as te co ff ee gr ou n ds ;F e- ca ta ly ze d gr ap h it iz at io n ;C \-A G vs . h ar d ca rb on 15 00 °C C -A G ar ou n d 28 6 m A h g− 1 IC E 85 .5 % ;c h ar ge /d is ch ar ge sp li t n ot av ai la bl e fr om ab st ra ct St ab le at va ri ou s cu rr en t de n si ti es B or ge s et al ., J. Po w er So ur ce s 20 26 (r ef .8 2\) N b- do pe d bi og ra ph it e fr om co ff ee h us k bi om as s N ot di re ct ly co m pa ra bl e Sp ec i c di sc h ar ge ca pa ci ty 37 5 m A h g− 1 at 0\. 2C C h ar ge va lu e n ot se pa ra te d in ab st ra ct H ig h cy cl in g st ab il it y; fu ll LI B ce ll al so as se m bl ed This journal is © The Royal Society of Chemistry 2026 Sustainable Energy Fuels, 2026, 10, 4881–4898 \| 4893 Paper Sustainable Energy \& FuelsSustainable Energy \& Fuels PaperConclusions This study demonstrates short-time hydrothermal carboniza- tion as a precursor-architecture strategy for low-temperature graphitization of Fe-impregnated Japanese cedarwood. A 15 min HTC step at 250 °C forms an iron–carbon hydrochar containing reducible mixed iron oxide domains, including Fe3O4, embedded within a reactive carbon matrix. During annealing at 1000 °C, these domains serve as spatially preor- ganized iron reservoirs that are converted into Fe and/or Fe3C catalytic phases, promoting graphitic layer growth. Subsequent acid washing was used to leach acid-soluble and exposed Fe- containing species, while mild air oxidation preferentially removed reactive or defect-rich carbon. No crystalline Fe- containing phases were detected by XRD aer washing, although trace residual Fe cannot be excluded without bulk elemental quantication. The resulting biomass-derived graphite, used without post-synthetic surface coating, exhibits graphite-like stacking, low Raman disorder, and local single- crystal-like graphitic domains within an interconnected sheet network. As a lithium-ion battery anode, the material delivers 341/317 mAh g−1 lithiation/delithiation capacities at 1C and exhibits reproducible lithiation behavior within each rate step up to 10C, while high-rate delithiation remains limited under the present test conditions. Thus, the main advantage of the present BGC is not the highest absolute capacity among biomass-derived graphites, but the combination of short precursor organization, 1000 °C graphitization, operation without post-synthetic surface coating, local graphitic ordering, and high-rate discharge capability. The rate-limited charge/ delithiation branch at high C-rates further identies electrode densication, particle-size control, and interfacial optimization as key targets for future fast-charge operation.Experimental Materials and chemicals Japanese cedarwood (Cryptomeria japonica) chips collected from Kawasaki Town, Miyagi Prefecture, Japan, were milled and sieved to obtain cedarwood sawdust with a particle size of#600 mm (hereaer CSD), which was used as the biomass precursor. Fe(NO3)3$9H2O (99.0%, Wako Pure Chemicals, Japan) was used as the graphitization catalyst. HCl (35.0–37.0%, Wako Pure Chemicals, Japan) was used to leach acid-soluble and exposed Fe-containing species from the graphitized products. Ultrapure water produced by a pure water generator (WG-220, Yamato Kagaku, Japan) was used in this experiment. Samples are designated as X h/m\_250\_YD, where X represents the residence time during hydrothermal carbonization (h = hours, m = minutes), 250 indicates the constant reaction temperature (°C), and YD denotes the number of impregnation days.CSD catalyst impregnation In a beaker, CSD (10 g, 600 mm) was impregnated by soaking in an aqueous Fe(NO3)3$9H2O solution (40 g Fe L−1, 100 mL) for 0– 4 days to vary iron incorporation (separate trials). The resulting4894 \| Sustainable Energy Fuels, 2026, 10, 4881–4898wet slurries were transferred directly to a 500 mL autoclave without drying and subjected to hydrothermal carbonization. This impregnation step was intended to promote broad Fe distribution within the biomass before catalytic graphitization. Primary carbonization Hydrothermal carbonization was carried out in a 500 mL stainless-steel autoclave equipped with an N2 inlet line, pres- sure gauge, and temperature controller. The reactor was lled, purged repeatedly with N2, and the internal pressure was adjusted to approximately 2 MPa. The reaction was conducted at 250 °C with stirring under 300 rpm for the desired residence time. Aer cooling, the slurry was discharged and ltered through a 0.45 mm OMNIPORE™ membrane (Merck Millipore). The recovered hydrochar was washed several times with ultrapure water and dried overnight at 105 °C. The HLP was collected directly aer ltration without additional dilution or washing, thereby preserving the native concentration of dissolved organics and lignin for subsequent recovery. Secondary carbonization (catalytic graphitization) The carbonization process was carried out using a high- temperature electric tubular furnace (FULL-TECH). The furnace temperature was controlled using a temperature controller. Nitrogen gas was supplied from a cylinder through a ow meter, and the exhaust valve was kept open throughout the process to maintain continuous ow. Aer HTC, 3.0 g of the dried hydrochar was placed in the furnace, and N2 gas was supplied at 500 mL min−1. The sample was heated to 1000 °C at a rate of ∼16 °C min−1 and maintained at this temperature for 1 h. Aer the holding period, the furnace was allowed to cool naturally to room temperature under continuous N2 ow. The carbonized product (∼1.5 g) was subsequently mixed with 200 mL of HCl (2 mol L−1) and allowed to stand overnight to leach acid-soluble and exposed inorganic species, including Fe-containing species. The solid was recovered using a 0.45 mm OMNIPORE™ membrane (Merck Millipore), washed several times with ultrapure water, and dried overnight at 105 °C in a constant-temperature oven to obtain the biomass-derived graphitic carbon (BGC). Air calcination The tertiary calcination process was carried out using a high- temperature electric tubular furnace (FULL-TECH). The furnace temperature was controlled using a temperature controller. Air was supplied from a cylinder through a ow meter, and the exhaust valve was kept open throughout the process to maintain continuous ow. Aer acid washing and drying, 1.0 g of BGC was placed in the furnace, and air was supplied at 500 mL min−1. The sample was heated to 400 °C at a rate of ∼16 °C min−1 and maintained at this temperature for 1 h. Aer the holding period, the furnace was allowed to cool naturally to room temperature under continuous air ow. The process resulted in approximately 98% of the calcined, highly crystalline graphitic carbon successfully recovered.This journal is © The Royal Society of Chemistry 2026Paper Sustainable Energy \& FuelsMaterials characterization and analysis The BGC samples were characterized by XRD (Ultima IV, RIGAKU, Japan) using Cu Ka radiation. Baseline correction was applied to the XRD patterns prior to analysis and plotting. The Scherrer equation was used to estimate crystallite dimensions from XRD peak broadening. The equation is as follows: L ¼ lK FWHM cos q (1) where L is the crystallite height (Lc) or lateral size (La), in nm, K is the Scherrer constant (0.91) for Lc and (1.84) for La, l is the X- ray wavelength (0.15443 nm for Cu Ka2 radiation), FWHM is the full width at half maximum of the diffraction peak; the values listed in Table 1 are in degrees and were converted to radians for the calculation, q is the Bragg angle. For interlayer distance (d002) d002 ¼ l 2 sin q (2) where, d002 is the interlayer distance (in nm), l is the X-ray wavelength (0.15443 nm for Cu Ka2 radiation), q is the Bragg angle. Raman spectra were obtained using a RAMANforce micro- scope with a 532 nm excitation laser. The integrated ID/IG ratio was used to estimate the crystallite size (La) via the Tuinstra– Koenig relation. LaðnmÞ ¼ 2:4�  10�10$l4 ID=IG Microstructure was observed using TEM (HT-7500, Hitachi) and TEM-EDS (JEM-2100F, JEOL). Fe content in the hydrochar was measured using ICP-OES (Thermo iCAP 6000, 213.859 nm). The elemental composition of the raw CSD was determined by CHNSO analysis (Elementar vario EL cube) for carbon yield evaluation. Thermogravimetric measurements were performed using a simultaneous DTA-TG analyzer (DTG-60AH, Shimadzu, Japan). For the hydrochar samples, the temperature was initially increased from 30 to 105 °C at a heating rate of 10 °C min−1 under an air ow of 100 mL min−1 and held at 105 °C for 15 min. The temperature was then increased to 1000 °C at 10 °C min−1, and for the graphitized samples, the temperature was increased from 30 to 105 °C at 10 °C min−1 under a nitrogen ow of 100 mL min−1 and held at 105 °C for 15 min. The temperature was subsequently increased to 450 °C at 10 °C min−1 and held for 10 min, followed by heating to 900 °C at the same rate of 10 °C min−1. The Fe coordination environments of the hydrochar samples were analyzed using the Fe K-edge X-ray absorption near-edge structure (XANES) and extended X-ray absorption ne structure (EXAFS). XAFS measurements were performed at the BL-9A beamline of the Photon Factory, KEK, Ibaraki, Japan. The energy calibration was carried out using a standard Fe foil. XAFS data processing was performed using the Athena program within the Demeter soware package.83 To obtain the EXAFS radialThis journal is © The Royal Society of Chemistry 2026distribution function in R-space, the extracted c(k) functions were k3-weighted and Fourier transformed over a k range of 3–12 Å−1 Electrode fabrication Electrode slurries were prepared by dispersing post-air-treated BGC as active material, an acetylene black conductive agent (Denka Black, HS-100), and a polyvinylidene uoride (PVDF) binder at an optimized mass ratio of 90 : 3 : 7 wt% in N-methyl- 2-pyrrolidone (NMP). The mixture was homogenized for 12 h and doctor-blade coated onto a 10 mm thick copper current collector (without carbon coating) with a 300 mm wet gap clearance. Aer vacuum drying to eliminate residual NMP, the composite lm was consolidated under a 5-ton pressing load, yielding an average active mass loading of 2.8 mg cm−2 and a structural electrode density of 0.66 g cm−3. Circular working electrode disks were subsequently punched out for cell integration. Electrochemical characterization Electrochemical performance was evaluated using standard CR2032-type coin cells assembled as half-cells inside an Ar- lled glovebox (moisture/oxygen \< 0.1 ppm) at 25 ± 3 °C. The punched BGC electrode disk served as the working electrode, paired against a pure metallic lithium disk reference/counter electrode and isolated by a three-layer polymeric membrane separator (UP3085). The liquid electrolyte was 1.0 mol L−1 LiPF6 in a binary solvent system of ethylene carbonate (EC) and di- ethyl carbonate (DEC) (1 : 1 v/v). Specic capacities were normalized to the mass of active material, and 371.9 mAh g−1 was used as the theoretical graphite-capacity reference. Before the rate-capability measurements, the cells used for the rate tests underwent a three-cycle galvanostatic condi- tioning protocol at 0.1C. The initial-cycle data shown in Fig. 7d was obtained using separate freshly assembled cells. Due to the intrinsic diffusion resistance of the thick-lm bio-graphite matrix, the initial lithiation step was governed by an extended constant current–constant voltage (CC–CV) sequence: CC lith- iation at 0.1C down to 0.005 V with a maximum time limit of 30 h, followed by a CV step at 0.005 V until the current decayed to a 0.05C cutoff threshold (5 h maximum duration). Aer a 10 min open-circuit rest period, CC delithiation was per- formed at 0.1C up to an upper cutoff potential of 1.6 V (15 h maximum duration). The specic discharge capacity recorded on the 3rd conditioning cycle established the exact 1C bench- mark for subsequent rate calculation. To decouple the independent kinetic transport resistances governing lithium insertion and extraction, two separate sets of conditioned coin cells were deployed for asymmetric rate capability assessments: Set A (lithiating kinetics): variable-current CC lithiation was applied at progressive rates (0.1C, 0.5C, 1C, 2C, 5C, and 10C; ve consecutive cycles per block) down to 0.005 V, followed by a 10 min rest phase, and a xed baseline CC delithiation at 0.1C up to 1.6 V. Set B (delithiating kinetics): symmetric CC–CV lithiation was rst conducted at a xed baseline of 0.1C down to 0.005 V (CVSustainable Energy Fuels, 2026, 10, 4881–4898 \| 4895Sustainable Energy \& Fuels Paperstep capped at 0.05C for a maximum of 1 h). Following a 10 min rest phase, asymmetric variable-current CC delithiation was performed up to 1.6 V across the matching rate sequence (0.1C to 10C; 5 continuous cycles per block). Cyclic voltammetry (CV) was conducted on a separate conditioned cell from its open-circuit voltage over a potential window of 0.0–1.5 V vs. Li/Li+ at a constant scan rate of 0.1 mV s−1 for 3 continuous cycles.Author contributions Preethi Perianayagam: writing – original dra, visualization, validation, methodology, investigation, formal analysis, data curation. Edwin Osebe Nyangau: validation, formal analysis, writing – review \& editing. Futa Imaizumi: investigation. Naoka Nagamura: formal analysis, Hideharu Niwa: formal analysis, Takashi Itoh: resources, supervision. Masaru Watanabe: project administration, methodology, writing – review \& editing, supervision, resources. Yuta Nakayasu: writing – review \& edit- ing, visualization, validation, supervision, resources, project administration, methodology, funding acquisition, conceptualization.Conflicts of interest There are no conicts to declare.Data availability Most of the data presented in this paper are included in the main manuscript, and the supplementary information (SI), and additional data are available from the corresponding author upon reasonable request. Supplementary information is avail- able. See DOI: https://doi.org/10.1039/d6se00774k.Acknowledgements This work was also supported by Environment Research and Technology Development Fund (grant No. JPMEERF20223C04 and JPMEERF20263005) from the Environmental Restoration and Conservation Agency, Ministry of the Environment of Japan; the Kurita Water and Environment Foundation (KWEF) (grant no. 25A028); the Japan Society for the Promotion of Science (JSPS) KAKENHI (grant no. 25K21634); and Tohoku Initiative for Fostering Global Researchers for Interdisciplinary Sciences (TI-FRIS) under the Strategic Professional Develop- ment Program for Young Researchers of the Ministry of Education, Culture, Sports, Science and Technology (MEXT). The authors also acknowledge the generous support from FRIS CoRE, Tohoku University, a shared research facility. We thank Dr Makoto Nagasako for his support with the TEM observation and Dr Hitoshi Abe for his support with XAFS analysis. This work utilizes AI-based tools to assist with language editing and manuscript preparation. The authors take full responsibility for the content of the manuscript.4896 \| Sustainable Energy Fuels, 2026, 10, 4881–4898References 1 B. P. Thapaliya, A. S. Ivanov, H. Y. Chao, M. Lamm, M. Chi, H. M. Meyer, X. G. Sun, T. Aytug, S. Dai and S. M. Mahurin, Carbon, 2023, 212, 118151, DOI: 10.1016/ j.carbon.2023.118151. 2 S. Bhattacharyya, S. Roy, X. Lin, N. Campagnol, A. Vlad and P. M. Ajayan, Nat. Rev. Mater., 2026, 11, 65–78, DOI: 10.1038/s41578-025-00848-5. 3 M. Armand and J. M. Tarascon, Nature, 2008, 451, 652–657, DOI: 10.1038/451652a. 4 D. Guerard and A. Herold, Carbon, 1975, 34, 337–345, DOI: 10.1016/0008-6223(75)90040-8. 5 J. Asenbauer, T. Eisenmann, M. Kuenzel, A. Kazzazi, Z. Chen and D. Bresser, Sustainable Energy Fuels, 2020, 4, 5387–5416, DOI: 10.1039/d0se00175a. 6 T. Shang, H. Zhan, Q. Gong, T. Zeng, P. Li and Z. Zeng, Energy, 2024, 297, 131269, DOI: 10.1016/ j.energy.2024.131269. 7 Y. Lan, X. Zhao, W. Zhang, L. Mu and S. Wang, Energy, 2022, 245, 123292, DOI: 10.1016/j.energy.2022.123292. 8 M. S. Soffian, F. Z. A. Halim, F. Aziz, M. A. Rahman, M. A. M. Amin and D. N. A. Chee, Environ. Adv., 2022, 9, 100259, DOI: 10.1016/j.envadv.2022.100259. 9 W. J. Sagues, J. Yang, N. Monroe, S. Han, T. Vinzant, M. Yung, H. Jameel, M. Nimlos and S. Park, Green Chem., 2020, 22, 7093–7108, DOI: 10.1039/D0GC02286A. 10 T. Vook, S. C. Dey, J. Yang, M. Nimlos, S. Park, S. Han and W. J. Sagues, J. Energy Storage, 2023, 73, 109242, DOI: 10.1016/j.est.2023.109242. 11 M. Sevilla, C. Sanch́ıs, T. Valdés-Soh, E. Morallón and A. B. Fuertes, J. Phys. Chem. C, 2007, 111, 9749–9756, DOI: 10.1021/jp072246x. 12 B. A. Lim, S. Lim, Y. L. Pang, S. H. Shuit and S. H. Kuan, Renewable Sustainable Energy Rev., 2023, 184, 113451, DOI: 10.1016/j.rser.2023.113451. 13 S. Rigollet, E. Weiss-Hortala, G. Flamant and A. Nzihou, Chem. Eng. J., 2024, 496, 153795, DOI: 10.1016/ j.cej.2024.153795. 14 M. Komiyama, Catal. Rev., 1985, 27(2), 341–372, DOI: 10.1080/01614948508064738. 15 G. Domazetis, J. Liesegang and B. D. James, Fuel Process. Technol., 2005, 86(5), 463–486, DOI: 10.1016/ j.fuproc.2004.03.009. 16 K. Bru, J. Blin, A. Julbe and G. Volle, J. Anal. Appl. Pyrolysis, 2007, 78(2), 291–300, DOI: 10.1016/j.jaap.2006.08.006. 17 G. Cheng, H. Li, J. Fang, X. Wang, J. Li, J. Chang, N. Teng and J. Wang, Carbon Lett., 2025, 35, 441–467, DOI: 10.1007/ s42823-025-00872-z. 18 S. Xia, H. Yang, W. Lu, N. Cai, H. Xiao, X. Chen, Y. Chen, X. Wang, S. Wang, P. Wu and H. Yang, Energy, 2022, 239, 122262, DOI: 10.1016/j.energy.2021.122262. 19 M. A. A. Farid, A. L. T. Zheng, T. Tsubota and Y. Andou, J. Anal. Appl. Pyrolysis, 2023, 173, 106064, DOI: 10.1016/ j.jaap.2023.106064.This journal is © The Royal Society of Chemistry 2026[https://doi.org/10.1039/d6se00774k](https://doi.org/10.1039/d6se00774k)[https://doi.org/10.1016/j.carbon.2023.118151](https://doi.org/10.1016/j.carbon.2023.118151)[https://doi.org/10.1016/j.carbon.2023.118151](https://doi.org/10.1016/j.carbon.2023.118151)[https://doi.org/10.1038/s41578-025-00848-5](https://doi.org/10.1038/s41578-025-00848-5)[https://doi.org/10.1038/451652a](https://doi.org/10.1038/451652a)[https://doi.org/10.1016/0008-6223(75)90040-8](<https://doi.org/10.1016/0008-6223(75)90040-8>)[https://doi.org/10.1039/d0se00175a](https://doi.org/10.1039/d0se00175a)[https://doi.org/10.1016/j.energy.2024.131269](https://doi.org/10.1016/j.energy.2024.131269)[https://doi.org/10.1016/j.energy.2024.131269](https://doi.org/10.1016/j.energy.2024.131269)[https://doi.org/10.1016/j.energy.2022.123292](https://doi.org/10.1016/j.energy.2022.123292)[https://doi.org/10.1016/j.envadv.2022.100259](https://doi.org/10.1016/j.envadv.2022.100259)[https://doi.org/10.1039/D0GC02286A](https://doi.org/10.1039/D0GC02286A)[https://doi.org/10.1016/j.est.2023.109242](https://doi.org/10.1016/j.est.2023.109242)[https://doi.org/10.1021/jp072246x](https://doi.org/10.1021/jp072246x)[https://doi.org/10.1016/j.rser.2023.113451](https://doi.org/10.1016/j.rser.2023.113451)[https://doi.org/10.1016/j.cej.2024.153795](https://doi.org/10.1016/j.cej.2024.153795)[https://doi.org/10.1016/j.cej.2024.153795](https://doi.org/10.1016/j.cej.2024.153795)[https://doi.org/10.1080/01614948508064738](https://doi.org/10.1080/01614948508064738)[https://doi.org/10.1016/j.fuproc.2004.03.009](https://doi.org/10.1016/j.fuproc.2004.03.009)[https://doi.org/10.1016/j.fuproc.2004.03.009](https://doi.org/10.1016/j.fuproc.2004.03.009)[https://doi.org/10.1016/j.jaap.2006.08.006](https://doi.org/10.1016/j.jaap.2006.08.006)[https://doi.org/10.1007/s42823-025-00872-z](https://doi.org/10.1007/s42823-025-00872-z)[https://doi.org/10.1007/s42823-025-00872-z](https://doi.org/10.1007/s42823-025-00872-z)[https://doi.org/10.1016/j.energy.2021.122262](https://doi.org/10.1016/j.energy.2021.122262)[https://doi.org/10.1016/j.jaap.2023.106064](https://doi.org/10.1016/j.jaap.2023.106064)[https://doi.org/10.1016/j.jaap.2023.106064](https://doi.org/10.1016/j.jaap.2023.106064)Paper Sustainable Energy \& Fuels20 E. O. Nyangau, H. Abe, K. Haga, C. Ooka, K. Hayashida, N. Nagamura, K. Takeyasu, M. Watanabe and Y. Nakayasu, J. Power Sources, 2025, 653, 237784, DOI: 10.1016/ j.jpowsour.2025.237784. 21 H. Abe, Y. Nakayasu, K. Haga andM. Watanabe, Glob. Chall., 2023, 7, 2300112, DOI: 10.1002/gch2.202300112. 22 H. Jeong, J. Kim, S. Lee, D. U. Kim, J. Kim and J. Yang, J. Alloys Compd., 2025, 1020, 179485, DOI: 10.1016/ j.jallcom.2025.179485. 23 H. You, J. Hui, Y. Zhou, K. Vittore, J. Zhang, L. E. Chaney, S. Chinta, Y. Zhao, G. Lim, D. Lee, E. A. Ainsworth, J. B. Dunn, V. P. Dravid, M. C. Hersam and S. J. Rowan, Small, 2024, 20, 2406669, DOI: 10.1002/smll.202406669. 24 K. Jurkiewicz, B. Liszka, P. Gancarz, S. Smykała, D. Zygadło, P. Nokielski, T. Lamrani, E. Talik, R. Wrzalik, M. Walkowiak and J. Ilavsky, Adv. Funct. Mater., 2024, 34, 2410409, DOI: 10.1002/adfm.202410409. 25 L. Lower, S. M. Rowland, M. Regula, K. Iisa, Z. A. Combs, S. Park, T. Vries, T. Vries, M. R. Nimlos and W. Joe Sagues, ChemSusChem, 2025, 18, e202402509, DOI: 10.1002/ cssc.202402509. 26 H. Weldekidan, A. K. Mohanty and M. Misra, ACS Environ. Au, 2022, 2, 510–522, DOI: 10.1021/acsenvironau.2c00029. 27 The Ministry of Agriculture, Forestry and Fisheries, Japan, https://www.rinya.maff.go.jp/j/sin\_riyou/kafun/data.html, accessed March 2022. 28 N. Phaiboonsilpa, K. Yamauchi, X. Lu and S. Saka, J. Wood Sci., 2010, 56, 331–338, DOI: 10.1007/s10086-009-1099-0. 29 Y. Kurata, Y. Mori, A. Ishida, M. Nakajima, N. Ito, M. Hamada, K. Yamashita, T. Fujiwara, M. Tonosaki and Y. Katayama, J. Wood Chem. Technol., 2018, 38, 254–263, DOI: 10.1080/02773813.2018.1434206. 30 K. Murakami, K. Fuda and M. Sugai, J. MMIJ, 2008, 124, 143– 147, DOI: 10.2473/journalofmmij.124.143. 31 T. Yamagishi, S. Yamauchi, K. Suzuki, T. Suzuki, Y. Kurimoto, T. Takayama and Y. Sakai, J. Wood Sci., 2020, 66, 82, DOI: 10.1186/s10086-020-01930-y. 32 N. Zhang, M. C. James, S. G. Krishnan, D. A. Keiser, B. Kehoe, T. Béguerie, C. E. White and A. Nzihou, Carbon, 2026, 260, 121906, DOI: 10.1016/j.carbon.2026.121906. 33 G. Davies and J. McGregor, ACS Omega, 2021, 6, 33000– 33009, DOI: 10.1021/acsomega.1c05116. 34 Y. Nakayasu, Y. Goto, Y. Katsuyama, T. Itoh and M. Watanabe, Carbon Trends, 2022, 8, 100190, DOI: 10.1016/j.cartre.2022.100190. 35 T. Yamagishi, S. Yamauchi, S. Shibutani, H. Suzuki, T. Takayama and Y. Sakai, J. Wood Sci., 2022, 68, 7, DOI: 10.1186/s10086-022-02014-9. 36 K. Lotz, A. Wütscher, H. Düdder, C. M. Berger, C. Russo, K. Mukherjee, G. Schwaab, M. Havenith and M. Muhler, ACS Omega, 2019, 4, 4448–4460, DOI: 10.1021/ acsomega.8b03369. 37 A. C. Ghogia, L. M. Romero Millán, C. E. White and A. Nzihou, ChemSusChem, 2023, 16, e202201864, DOI: 10.1002/cssc.202201864. 38 G. Gonnella, G. Ischia, L. Fambri and L. Fiori, Energies, 2022, 15, 950, DOI: 10.3390/en15030950.This journal is © The Royal Society of Chemistry 202639 L. G. Cançado, K. Takai, T. Enoki, M. Endo, Y. A. Kim, H. Mizusaki, N. L. Speziali, A. Jorio and M. A. Pimenta, Carbon, 2008, 46, 272–275, DOI: 10.1016/ j.carbon.2007.11.015. 40 R. F. Susanti, A. A. Arie, H. Kristianto and A. Suhendi, Ionics, 2019, 25, 3915–3925, DOI: 10.1007/s11581-019-02904-x. 41 E. Thompson, A. E. Danks, L. Bourgeois and Z. Schnepp, Green Chem., 2015, 17, 551–556, DOI: 10.1039/C4GC01673D. 42 R. D. Hunter, J. Ramı́rez-Rico and Z. Schnepp, J. Mater. Chem. A, 2022, 10, 4489–4516, DOI: 10.1039/d1ta09654k. 43 Z. Sun, D. Yao, C. Cao, Z. Zhang, L. Zhang, H. Zhu, Q. Yuan and B. Yi, J. Environ. Manage., 2022, 318, 115555, DOI: 10.1016/j.jenvman.2022.115555. 44 A. Gomez-Martin, Z. Schnepp and J. Ramı́rez-Rico, Chem. Mater., 2021, 33, 3087–3097, DOI: 10.1021/ acs.chemmater.0c04385. 45 M. Chen, L.-L. Shao, J.-J. Li, W.-J. Pei, M.-K. Chen and X.-H. Xie, RSC Adv., 2016, 6, 35228–35238, DOI: 10.1039/ C6RA01408A. 46 M. T. H. Siddiqui, S. Nizamuddin, H. A. Baloch, N. M. Mubarak, D. K. Dumbre, Inamuddin, A. M. Asiri, A. W. Bhutto, M. Srinivasan and G. J. Griffin, Environ. Chem. Lett., 2018, 16, 821–844, DOI: 10.1007/s10311-018- 0724-9. 47 H. Meng, Z. Chen, W. Wei, J. Xu, H. Duan, M. Zheng and B. J. Ni, npj Mater. Sustainability, 2025, 3, 7, DOI: 10.1038/ s44296-024-00047-3. 48 W. Yu, T. Sun, Z. Liu, J. Kou and C. Xu, ISIJ Int., 2014, 54, 56– 62, DOI: 10.2355/isijinternational.54.56. 49 M. Bastide d'Izard and S. Abanades, Chem. Eng. J. Adv., 2025, 24, 100925, DOI: 10.1016/j.ceja.2025.100925. 50 H. Okudera, A. Yoshiasa, K. Murai, M. Okube, T. Takeda and S. Kikkawa, J. Mineral. Petrol. Sci., 2012, 107, 127–132, DOI: 10.2465/jmps.110624. 51 D. K. Bora, A. Braun, S. Erat, O. Safonova, T. Graule and E. C. Constable, Curr. Appl. Phys., 2012, 12, 817–825, DOI: 10.1016/j.cap.2011.11.013. 52 A. Espinosa, et al.,Meas. Sci. Technol., 2012, 23, 015602, DOI: 10.1088/0957-0233/23/1/015602. 53 M. Miao, S. Zuo, Y. Zhao, Y. Wang, H. Xia, C. Tan and H. Gao, Carbon, 2018, 140, 504–507, DOI: 10.1016/ j.carbon.2018.09.018. 54 F. Herold, S. Prosch, N. Oefner, K. Brunnengräber, O. Leubner, Y. Hermans, K. Hofmann, A. Drochner, J. P. Hofmann, W. Qi and B. J. M. Etzold, Angew. Chem., Int. Ed., 2021, 60, 5898–5906, DOI: 10.1002/anie.202014862. 55 C. Chen, K. Sun, C. Huang, M. Yang, M. Fan, A. Wang, G. Zhang, B. Li, J. Jiang, W. Xu and J. Liu, Biochar, 2023, 5, 51, DOI: 10.1007/s42773-023-00229-7. 56 J. Kim, J. Kim, H. Park, Y. Kim and J. Yang, J. Power Sources, 2026, 663, 238867, DOI: 10.1016/j.jpowsour.2025.238867. 57 M. Prieto, H. Yue, N. Brun, G. J. Ellis, M. Naffakh and P. S. Shuttleworth, Polymers, 2024, 16, 2633, DOI: 10.3390/ polym16182633. 58 B. M. Ghanim, D. S. Pandey, W. Kwapinski and J. J. Leahy, Bioresour. Technol., 2016, 216, 373–380, DOI: 10.1016/ j.biortech.2016.05.087.Sustainable Energy Fuels, 2026, 10, 4881–4898 \| 4897[https://doi.org/10.1016/j.jpowsour.2025.237784](https://doi.org/10.1016/j.jpowsour.2025.237784)[https://doi.org/10.1016/j.jpowsour.2025.237784](https://doi.org/10.1016/j.jpowsour.2025.237784)[https://doi.org/10.1002/gch2.202300112](https://doi.org/10.1002/gch2.202300112)[https://doi.org/10.1016/j.jallcom.2025.179485](https://doi.org/10.1016/j.jallcom.2025.179485)[https://doi.org/10.1016/j.jallcom.2025.179485](https://doi.org/10.1016/j.jallcom.2025.179485)[https://doi.org/10.1002/smll.202406669](https://doi.org/10.1002/smll.202406669)[https://doi.org/10.1002/adfm.202410409](https://doi.org/10.1002/adfm.202410409)[https://doi.org/10.1002/cssc.202402509](https://doi.org/10.1002/cssc.202402509)[https://doi.org/10.1002/cssc.202402509](https://doi.org/10.1002/cssc.202402509)[https://doi.org/10.1021/acsenvironau.2c00029](https://doi.org/10.1021/acsenvironau.2c00029)[https://www.rinya.maff.go.jp/j/sin\_riyou/kafun/data.html](https://www.rinya.maff.go.jp/j/sin_riyou/kafun/data.html)[https://doi.org/10.1007/s10086-009-1099-0](https://doi.org/10.1007/s10086-009-1099-0)[https://doi.org/10.1080/02773813.2018.1434206](https://doi.org/10.1080/02773813.2018.1434206)[https://doi.org/10.2473/journalofmmij.124.143](https://doi.org/10.2473/journalofmmij.124.143)[https://doi.org/10.1186/s10086-020-01930-y](https://doi.org/10.1186/s10086-020-01930-y)[https://doi.org/10.1016/j.carbon.2026.121906](https://doi.org/10.1016/j.carbon.2026.121906)[https://doi.org/10.1021/acsomega.1c05116](https://doi.org/10.1021/acsomega.1c05116)[https://doi.org/10.1016/j.cartre.2022.100190](https://doi.org/10.1016/j.cartre.2022.100190)[https://doi.org/10.1186/s10086-022-02014-9](https://doi.org/10.1186/s10086-022-02014-9)[https://doi.org/10.1021/acsomega.8b03369](https://doi.org/10.1021/acsomega.8b03369)[https://doi.org/10.1021/acsomega.8b03369](https://doi.org/10.1021/acsomega.8b03369)[https://doi.org/10.1002/cssc.202201864](https://doi.org/10.1002/cssc.202201864)[https://doi.org/10.3390/en15030950](https://doi.org/10.3390/en15030950)[https://doi.org/10.1016/j.carbon.2007.11.015](https://doi.org/10.1016/j.carbon.2007.11.015)[https://doi.org/10.1016/j.carbon.2007.11.015](https://doi.org/10.1016/j.carbon.2007.11.015)[https://doi.org/10.1007/s11581-019-02904-x](https://doi.org/10.1007/s11581-019-02904-x)[https://doi.org/10.1039/C4GC01673D](https://doi.org/10.1039/C4GC01673D)[https://doi.org/10.1039/d1ta09654k](https://doi.org/10.1039/d1ta09654k)[https://doi.org/10.1016/j.jenvman.2022.115555](https://doi.org/10.1016/j.jenvman.2022.115555)[https://doi.org/10.1021/acs.chemmater.0c04385](https://doi.org/10.1021/acs.chemmater.0c04385)[https://doi.org/10.1021/acs.chemmater.0c04385](https://doi.org/10.1021/acs.chemmater.0c04385)[https://doi.org/10.1039/C6RA01408A](https://doi.org/10.1039/C6RA01408A)[https://doi.org/10.1039/C6RA01408A](https://doi.org/10.1039/C6RA01408A)[https://doi.org/10.1007/s10311-018-0724-9](https://doi.org/10.1007/s10311-018-0724-9)[https://doi.org/10.1007/s10311-018-0724-9](https://doi.org/10.1007/s10311-018-0724-9)[https://doi.org/10.1038/s44296-024-00047-3](https://doi.org/10.1038/s44296-024-00047-3)[https://doi.org/10.1038/s44296-024-00047-3](https://doi.org/10.1038/s44296-024-00047-3)[https://doi.org/10.2355/isijinternational.54.56](https://doi.org/10.2355/isijinternational.54.56)[https://doi.org/10.1016/j.ceja.2025.100925](https://doi.org/10.1016/j.ceja.2025.100925)[https://doi.org/10.2465/jmps.110624](https://doi.org/10.2465/jmps.110624)[https://doi.org/10.1016/j.cap.2011.11.013](https://doi.org/10.1016/j.cap.2011.11.013)[https://doi.org/10.1088/0957-0233/23/1/015602](https://doi.org/10.1088/0957-0233/23/1/015602)[https://doi.org/10.1016/j.carbon.2018.09.018](https://doi.org/10.1016/j.carbon.2018.09.018)[https://doi.org/10.1016/j.carbon.2018.09.018](https://doi.org/10.1016/j.carbon.2018.09.018)[https://doi.org/10.1002/anie.202014862](https://doi.org/10.1002/anie.202014862)[https://doi.org/10.1007/s42773-023-00229-7](https://doi.org/10.1007/s42773-023-00229-7)[https://doi.org/10.1016/j.jpowsour.2025.238867](https://doi.org/10.1016/j.jpowsour.2025.238867)[https://doi.org/10.3390/polym16182633](https://doi.org/10.3390/polym16182633)[https://doi.org/10.3390/polym16182633](https://doi.org/10.3390/polym16182633)[https://doi.org/10.1016/j.biortech.2016.05.087](https://doi.org/10.1016/j.biortech.2016.05.087)[https://doi.org/10.1016/j.biortech.2016.05.087](https://doi.org/10.1016/j.biortech.2016.05.087)Sustainable Energy \& Fuels Paper59 M. T. Reza, E. Rottler, L. Herklotz and B. Wirth, Bioresour. Technol., 2015, 182, 336–344, DOI: 10.1016/ j.biortech.2015.02.024. 60 H. D. Pham, T. Shelley, P. K. Annamalai, J. Feldman, T. T. Nguyen, A. Helwig and A. K. Nanjundan, Small, 2025, 21, e09226, DOI: 10.1002/smll.202509226. 61 J. O. Ighalo, F. C. Akaeme, J. Georgin, J. S. de Oliveira and D. S. P. Franco, Sustainability, 2025, 17, 1660, DOI: 10.3390/su17041660. 62 G. Caygill, M. Zanr and A. Gavriilidis, Org. Process Res. Dev., 2006, 10, 539–552, DOI: 10.1021/op050133a. 63 J. J. Carberry, Ind. Eng. Chem., 1966, 58, 40. 64 S. Yu, J. He, Z. Zhang, Z. Sun, M. Xie, Y. Xu, X. Bie, Q. Li, Y. Zhang, M. Sevilla, M. M. Titirici and H. Zhou, Adv. Mater., 2024, 36, 2307412, DOI: 10.1002/adma.202307412. 65 S. Rigollet, T. Béguerie, E. Weiss-Hortala, G. Flamant and A. Nzihou, Sci. Rep., 2025, 15, 6418, DOI: 10.1038/s41598- 025-91204-8. 66 A. Shalaby, D. Nihtianova, P. Markov, A. D. Staneva, R. S. Iordanova and Y. B. Dimitriev, Bulg. Chem. Commun., 2015, 47, 291–295. 67 K. K. Garlapati, S. Ghosh, J. Dutta, B. B. Panigrahi and S. K. Martha, Adv. Energy Mater., 2025, 15, 2500501, DOI: 10.1002/aenm.202500501. 68 A. Wang, P. Dhamelincourt, J. Dubessy, D. Guerard, P. Landais and M. Lelaurain, Carbon, 1989, 27, 209–218, DOI: 10.1016/0008-6223(89)90125-5. 69 C. Liang, Y. Chen, M. Wu, K. Wang, W. Zhang, Y. Gan, H. Huang, J. Chen, Y. Xia, J. Zhang, S. Zheng and H. Pan, Nat. Commun., 2021, 12, 119, DOI: 10.1038/s41467-020- 20380-0. 70 S. C. Dey, L. Lower, T. Vook, M. N. Islam, W. J. Sagues, S. D. Han, M. R. Nimlos, S. S. Kelley and S. Park, Green Chem., 2024, 26, 8840–8853, DOI: 10.1039/D4GC01647E. 71 M. A. Pimenta, G. Dresselhaus, M. S. Dresselhaus, L. G. Cançado, A. Jorio and R. Saito, Phys. Chem. Chem. Phys., 2007, 9, 1276–1290, DOI: 10.1039/b613962k.4898 \| Sustainable Energy Fuels, 2026, 10, 4881–489872 J. W. Long, M. Laskoski, T. M. Keller, K. A. Pettigrew, T. N. Zimmerman, S. B. Qadri and G. W. Peterson, Carbon, 2010, 48, 501–508, DOI: 10.1016/j.carbon.2009.09.068. 73 M. Sathish, T. Tomai and I. Honma, J. Power Sources, 2012, 217, 85–91, DOI: 10.1016/j.jpowsour.2012.05.099. 74 Z. Chen, D. L. Danilov, L. H. J. Raijmakers, K. Chayambuka, M. Jiang, L. Zhou, J. Zhou, R.-A. Eichel and P. H. L. Notten, J. Power Sources, 2021, 509, 230345. 75 T. Xing, T. Ramireddy, L. H. Li, D. Gunzelmann, H. Zeng, W. Qi, S. Zhou and Y. Chen, Phys. Chem. Chem. Phys., 2015, 17, 5084–5089. 76 V. Sharova, A. Moretti, G. A. Giffin, D. V. Carvalho and S. Passerini, C, 2017, 3, 22, DOI: 10.3390/c3030022. 77 S. C. Dey, B. J. Worfolk, W. J. Sagues, R. K. Bhardwaj, B. J. Tremolet de Villers, S. M. Rowland, M. R. Nimlos and S. Park, Energy Fuels, 2025, 39, 11372–11387, DOI: 10.1021/ acs.energyfuels.5c01132. 78 M. Gulas, F. Delort, R. Gilardi, G. Juri, L. Ostinelli, F. Rauscher, X. Wang and S. Zürcher, ACS Omega, 2026, 11, 9435–9450, DOI: 10.1021/acsomega.5c09286. 79 F. Wang, Y. Wang, Z. Guan, J. Wei, S. He, Z. Zhong, H. Chen and P. Feng, Sustainable Energy Fuels, 2025, 9, 3293–3303, DOI: 10.1039/D4SE01602E. 80 T. A. Thomas, P. Ellison, D. Nam, J. Pepas, G. Zhang, S. G. Yoon, K. A. Cavallaro, E. P. Alsaç, C. Wang, H. Chen and M. T. McDowell, MRS Energy Sustainability, 2026, DOI: 10.1557/s43581-026-00161-w. 81 J. Kim, D. Yu, D. Kim, J. Kim and J. Yang, FlatChem, 2025, 51, 100867, DOI: 10.1016/j.atc.2025.100867. 82 I. O. Borges, O. A. T. Dias, A. K. Nair, C. M. Da Silva, C. H. Amon, A. R. Sanadi, G. H. D. Tonoli and M. Sain, J. Power Sources, 2026, 668, 239371, DOI: 10.1016/ j.jpowsour.2026.239371. 83 B. Ravel and M. Newville, J. Synchrotron Radiat., 2005, 12, 537–541.This journal is © The Royal Society of Chemistry 2026[https://doi.org/10.1016/j.biortech.2015.02.024](https://doi.org/10.1016/j.biortech.2015.02.024)[https://doi.org/10.1016/j.biortech.2015.02.024](https://doi.org/10.1016/j.biortech.2015.02.024)[https://doi.org/10.1002/smll.202509226](https://doi.org/10.1002/smll.202509226)[https://doi.org/10.3390/su17041660](https://doi.org/10.3390/su17041660)[https://doi.org/10.1021/op050133a](https://doi.org/10.1021/op050133a)[https://doi.org/10.1002/adma.202307412](https://doi.org/10.1002/adma.202307412)[https://doi.org/10.1038/s41598-025-91204-8](https://doi.org/10.1038/s41598-025-91204-8)[https://doi.org/10.1038/s41598-025-91204-8](https://doi.org/10.1038/s41598-025-91204-8)[https://doi.org/10.1002/aenm.202500501](https://doi.org/10.1002/aenm.202500501)[https://doi.org/10.1016/0008-6223(89)90125-5](<https://doi.org/10.1016/0008-6223(89)90125-5>)[https://doi.org/10.1038/s41467-020-20380-0](https://doi.org/10.1038/s41467-020-20380-0)[https://doi.org/10.1038/s41467-020-20380-0](https://doi.org/10.1038/s41467-020-20380-0)[https://doi.org/10.1039/D4GC01647E](https://doi.org/10.1039/D4GC01647E)[https://doi.org/10.1039/b613962k](https://doi.org/10.1039/b613962k)[https://doi.org/10.1016/j.carbon.2009.09.068](https://doi.org/10.1016/j.carbon.2009.09.068)[https://doi.org/10.1016/j.jpowsour.2012.05.099](https://doi.org/10.1016/j.jpowsour.2012.05.099)[https://doi.org/10.3390/c3030022](https://doi.org/10.3390/c3030022)[https://doi.org/10.1021/acs.energyfuels.5c01132](https://doi.org/10.1021/acs.energyfuels.5c01132)[https://doi.org/10.1021/acs.energyfuels.5c01132](https://doi.org/10.1021/acs.energyfuels.5c01132)[https://doi.org/10.1021/acsomega.5c09286](https://doi.org/10.1021/acsomega.5c09286)[https://doi.org/10.1039/D4SE01602E](https://doi.org/10.1039/D4SE01602E)[https://doi.org/10.1557/s43581-026-00161-w](https://doi.org/10.1557/s43581-026-00161-w)[https://doi.org/10.1016/j.flatc.2025.100867](https://doi.org/10.1016/j.flatc.2025.100867)[https://doi.org/10.1016/j.jpowsour.2026.239371](https://doi.org/10.1016/j.jpowsour.2026.239371)[https://doi.org/10.1016/j.jpowsour.2026.239371](https://doi.org/10.1016/j.jpowsour.2026.239371)- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes- Hydrothermally preorganized wood-derived graphite with local single-crystal-like domains for coating-free lithium-ion battery anodes