# Fileset

[ae-2025-02323d_Proof_hi.pdf](https://mdr.nims.go.jp/filesets/3f0a2b9a-b3e1-41a2-b133-d6038fe05676/download)

## Creator

[Mayeesha Marium](https://orcid.org/0009-0008-3366-0394), [Kentaro Aoki](https://orcid.org/0000-0003-4148-6070), Yang He, [Katsuhiro Yamamoto](https://orcid.org/0000-0003-1111-4735), Athchaya Suwansoontorn, Seiya Ikuta, [Mitsuo Hara](https://orcid.org/0000-0003-1829-5153), [Shusaku Nagano](https://orcid.org/0000-0002-3929-6377), [Yuki Nagao](https://orcid.org/0000-0003-1249-440X), [Kei Nishikawa](https://orcid.org/0000-0002-7718-7606), [Tsukasa Miyazaki](https://orcid.org/0000-0002-9124-2819), [Hiroyuki Aoki](https://orcid.org/0000-0001-7521-2743), [Shigeru Kobayashi](https://orcid.org/0000-0003-4997-8782), [Tomohito Sudare](https://orcid.org/0000-0002-9060-4291), [Taro Hitosugi](https://orcid.org/0000-0002-7795-0683), [Nobuyuki Zettsu](https://orcid.org/0000-0003-2838-3165)

## Rights

This document is the Accepted Manuscript version of a Published Work that appeared in final form in [Journal Title], copyright © 2025 American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see https://doi.org/10.1021/acsaem.5c02323.[In Copyright](http://rightsstatements.org/vocab/InC/1.0/)

## Other metadata

[Lyotropic Polymer Liquid Crystal Coating: Enabling Lamellar Ion-Conduction Pathways for Superior C-Rate Performance in NCM523 Cathodes](https://mdr.nims.go.jp/datasets/f266dbf3-c095-41fb-be27-b874d0927466)

## Fulltext

This document is confidential and is proprietary to the American Chemical Society and its authors. Do not  copy or disclose without written permission. If you have received this item in error, notify the sender and  delete all copies. Lyotropic Polymer Liquid Crystal Coating: Enabling Lamellar  Ionic-Conductive Highways for Superior C-Rate  Performance in NCM523 Cathodes Journal: ACS Applied Energy Materials Manuscript ID ae-2025-02323d Manuscript Type: Article Date Submitted by the  Author: 26-Jul-2025 Complete List of Authors: Marium, Mayeesha; Japan Synchrotron Radiation Research Institute  Aoki, Kentaro; Japan Advanced Institute of Science and Technology,  Materials Science Yamamoto, Katsuhiro; Nagoya Insititue of Technology, Life Science and  Applied Chemistry Suwansoontorn, Athchaya; Japan Advanced Institute of Science and  Technology, School of Materials Science Ikuta, Seiya; Japan Advanced Institute of Science and Technology Hara, Mitsuo; Kagawa University Faculty of Engineering,  Nagano, Shusaku; Rikkyo University College of Science, Department of  Chemistry Nagao, Yuki; Japan Advanced Institute of Science and Technology ,  School of Materials Science Nishikawa, Kei; National Institute for Materials Science, Center for Green  Research on Energy and Environmental Materials Miyazaki, Tsukasa; Kyoto University, Office of Society-Academia  Collaboration for Innovation Aoki, Hiroyuki; Japan Atomic Energy Agency, J-PARC Center Kobayashi, Shigeru; The University of Tokyo,  Sudare, Tomohito; The University of Tokyo,  Hitosugi, Taro; The University of Tokyo, Chemistry Zettsu, Nobuyuki; Shinshu University, Materials Chemistry &#32; ACS Paragon Plus Environment ACS Applied Energy MaterialsLyotropic Polymer Liquid Crystal Coating: Enabling  Lamellar Ionic-Conductive Highways for Superior C- Rate Performance in NCM523 CathodesMayeesha Mariuma⁑, Kentaro Aokib⁑, Katsuhiro Yamamotoc, Athchaya Suwansoontornb, Seiya Ikutab,  Mitsuo Harad, Shusaku Naganoe, Yuki Nagaob, Kei Nishikawaf, Tsukasa Miyazakig, Hiroyuki Aokih,  Shigeru Kobayashii, Tomohito Sudarei, Taro Hitosugii, and Nobuyuki Zettsu\* a, j1. a. Department of Materials Chemistry, Shinshu University, 4-17-1 Wakasato, Nagano, 380-8553  Japan2. b. School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1 Asahidai,  Nomi, Ishikawa, 923-1292, Japan3. c. Department of Life Science and Applied Chemistry, Graduate School of Engineering, Nagoya  Institute of Technology, 466-8555 Nagoya, Japan4. d. Department of Molecular Design \& Engineering, Graduate School of Engineering, Nagoya  University, Furo-cho, Chikusa, Nagoya, Aichi 464-8603, Japan5. e. Department of Chemistry, College of Science, Rikkyo University, 3-34-1 Nishi-ikebukuro,  Toshima, Tokyo 171-8501, Japan6. f. Rechargeable Battery Materials Group, Center for Green Research on Energy and Environmental  Materials, National Institute for Materials Science 1-1 Namiki, Tsukuba, Ibaraki 305-0044, Japan7. g. Office of Society-Academia Collaboration for Innovation, Kyoto University, Sakyou-ku, Kyoto  606-8501, Japan8. h. Materials and Life Science Division, J-PARC Center, Japan Atomic Energy Agency, 2-4  Shirakata, Tokai, Ibaraki 319-1195, Japan9. i. Department of Chemistry, The University of Tokyo, 113-0033 Tokyo, Japan10. j. Institute for Aqua-regeneration, Shinshu University, 4-17-1 Wakasato, Nagano, 380-8553 JapanPage 1 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60‡These authors contributed equally to work.  \*Corresponding Authors. zettsu@shinshu-u.ac.jp  &#32; &#32; &#32; &#32; &#32; &#32; &#32; &#32; &#32; &#32; &#32; Page 2 of 50 ACS Paragon Plus Environment ACS Applied Energy Materials 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60ABSTRACTHigh C-rate capability and energy-density stability are crucial for advanced lithium-ion  batteries (LIBs). However, these two characteristics typically conflict in conventional  systems. Herein, a lyotropic polymer liquid crystal (LPLC)-based coating was applied to  the surface of LiNi0.5Co0.2Mn0.3O2 (NCM523) cathode surface to constract a highly ion- conductive artificial cathode electrolyte interface (CEI) layer, aiming to supersede  traditional CEIs for LIBs. The coating material, composed of amphiphilic lithium- substituted alkyl-sulfonated polyimide (ASPI-Li) and an appropriate amount of organic  liquid electrolyte, forms nanoscale fluidic layers that act as ion-conducting highways,  increasing the local concentration of Li+ near the NCM523 surface. The layered  regulation of the liquid–fluid highly accelerated the ion diffusion kinetics at the  electrode/electrolyte interface and showed superior C-rate capability at ambient  temperatures compared to that of conventional LIB systems. The present work, using  molecular design, sheds new light on the development of next-generation artificial CEI  layers for various efficient and sustainable energy-storage systems.KeywordLyotropic polymer liquid crystal, polymer electrolyte, lithium-ion batteries, artificial CEIPage 3 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60IntroductionWith the growing demand for sustainable energy-storage devices with high power and  energy density, research on high-performance lithium-ion batteries (LIBs) has rapidly  expanded since their commercialization in the 1990s.1 The operation of LIBs involves the  sequential or simultaneous occurrence of a multitude of reactions that complicate the  investigation of their mechanisms. For example, although the degradation of liquid  electrolytes during battery cycling in a certain electrochemical potential window is known  to afford a solid electrolyte interface (SEI) and cathode-electrolyte interface (CEI),2 the  interactions of liquid electrolytes with electrode surfaces at the atomic/molecular level  remain poorly understood. Moreover, although LIBs have been widely used, the demand  for higher power densities necessitates the design of more efficient LIBs that enhance Li+  intercalation kinetics, accelerating charge and discharge reactions.The diffusion of lithium ions within the electrode's active material and the charge-transfer  (CT) kinetics at the phase boundaries are crucial factors influencing the C-rate of quick  charging; hence, investigating and improving these aspects are essential.3 For LIBs,  charge transfer involves Li+ diffusion within the electrolyte, followed by the desolvation,  adsorption, and diffusion of Li+ through the CEI and onto the active material surface, andPage 4 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Li+ insertion into the active material. Abe et al.4,5 reported that intercalation kinetics are  largely determined by Li+ desolvation rather than by Li+ diffusion through the CEI, further  demonstrating that the activation energy of desolvation is positively correlated with the  interaction between lithium ions and solvents. Li+ transfer at the ceramic-based solid  electrolyte/liquid electrolyte interface was also investigated. Electrochemical impedance  spectroscopy (EIS) revealed that the overall reaction kinetics were determined by the  activation energy of liquid electrolyte desolvation, which exceeded that of the solid  electrolyte. Jow et al.6 identified the conditions under which charge-transfer kinetics are  controlled by the desolvation of Li+ ions or their transport through the CEI. In particular,  at high temperatures, charge transfer may be limited by the diffusion of Li+ through the  active material bulk or through the CEI, whereas desolvation becomes the limiting factor  in the case of an amorphous electrolyte interface or a very thin CEI.Several strategies have been employed to modify cathode materials to enhance transport  kinetics and stability against capacity degradation. These include designing a core–shell  structure,7 introducing transition-metal concentration gradients8,9, and doping the  cathodes with functional materials.10,11 The most widely used approach to modifying  cathode materials for fast charging applications is surface modification with an artificial  coating.10,12–14 The structure and composition of the solid electrolyte interface formed onPage 5 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60the cathode’s surface from the reactions of the electrolytes play a key role in determining  the Li+ diffusion behaviors. As such, these artificial coatings can act as effective tools for  controlling interfacial processes for improved electrochemical properties.15 Several other  efforts have enhanced rate performance by modifying the surface environment during  cycling to achieve higher capacities at high C-rates.3,10,16–23 For example, Charles-Blin et  al demonstrated that increasing the local lithium ion concentration at the LiCoO2 surface,  using a Li+-conductive amorphous Li2B4O7 coating improved discharge kinetics.23  Similarly, the formation of an artificial CEI layer with Li-ion conductivity on a  LiNi0.8Mn0.1Co0.1O2 (NCM811) cathode surface, via a nucleophilic reaction between  polysulfides and vinylene carbonate (VC), protected NCM particles from electrolyte  corrosion while facilitating Li-ion transport.10 Although conductive organic polymeric  coatings have been explored to improve cyclic stability and rate performances of cathode  materials, most research has focused on using inorganic oxides as coating materials.14,24  Molecularly designed functional soft materials in the artificial CEI layer can provide  greater control over interface dynamics by exploiting their passive dynamic properties,  an advantage that inorganic materials do not possess.Among such materials, lyotropic liquid crystalline (LC) electrolytes have attracted  significant interest as structured electrolytes, owing to their ability to self-assemble intoPage 6 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60ordered ionic domains that support efficient Li-ion transport. These materials, typically  composed of amphiphilic small molecules or polymers, offer internal nanostructures and  soft-matter dynamics that are distinct from conventional liquid or solid electrolytes.  While LC-based electrolytes have been applied successfully in various battery systems,  their use has so far been limited to bulk ion transport media, and their potential as  interfacial modifiers remains largely unexplored.Early foundational work by Kerr et al. reported the spontaneous formation of lyotropic  mesophases from ionic surfactant-like small molecules, even in the absence of lithium  salts.25 This study highlighted the feasibility of using lyotropic phases for ion-conductive  nanostructures, although battery operation was not demonstrated. Building on this  concept, Sakuda et al. incorporated lithium salts into lyotropic LC systems and were the  first to demonstrate their electrochemical functionality in working lithium-ion batteries.26  These studies established the viability of LC electrolytes for practical applications,  particularly within the bulk electrolyte phase.More recently, LC-based electrolytes have gained increasing attention not only in  laboratory studies but also in practical device configurations for various LIB architectures.  Applications have expanded to include separators with carbonate-based systems,27, 28  aqueous quasi-solid-state systems,29 and lithium-metal batteries.30,31 These studiesPage 7 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60underscore the growing relevance of LC electrolytes in improving ion conductivity and  stability, though primarily in the context of bulk media. While most previous studies have  focused on LC materials as bulk electrolytes, their potential as functional interfacial  coatings for electrode surfaces has not yet been fully explored.In this study, we coated the surface of LiNi0.5Co0.2Mn0.3O2 (NCM523) with an  amphiphilic lithium-substituted alkyl-sulfonated polyimide (ASPI-Li), a lyotropic  polymer liquid crystal (LPLC), to enhance its electrochemical performance. Previously,  Ono et al. demonstrated that ASPI exhibits lyotropic self-organization under humid  conditions, forming structurally ordered films with high proton conductivity due to the  presence of flexible alkyl side chains.32, 33 Building on this insight, we anticipated that the  lyotropic nature of ASPI-Li would promote the formation of an organized interfacial  structure that facilitates lithium-ion transport at the cathode-electrolyte boundary.In fact, significant improvements in high-rate performance were observed upon coating  with ASPI-Li, accompanied by a reduction in the activation energy of charge-transfer, as  confirmed by electrochemical impedance spectroscopy (EIS). These results suggest that  the formation of a self-assembled interfacial environment enhanced ion accessibility and  interfacial kinetics. Furthermore, the ASPI-Li layer functions as a robust CEI, suppressing  parasitic reactions and stabilizing the NCM523 surface during cycling. The ultrathinPage 8 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60ASPI-Li coating thus acts as a multifunctional interfacial layer, combining  electrochemical protection with the advantages of structurally organized soft materials.Experimental SectionSynthesis of ASPI-LiThe polymer ASPI-Li was synthesized as follows (see also Figure S1): First, the  polymerization was conducted by the reaction of pyromellitic dianhydride and 3,3’- bis(sulfopropoxy)-4,4’-diaminobiphenyl with triethylamine (TEA) in m-cresol under an  Ar atmosphere at 150 oC for 6 h.32 The polymer was precipitated from ice-cold acetone  and then collected by centrifugation to obtain ASPI-TEA with tetraethylammonium as a  cation. Ion exchange from ASPI-TEA to ASPI-Li was performed by passing an aqueous  solution of the obtained polymer through an ion-exchange resin provided by Organo  Corporation. The degree of cation exchange was monitored from the -CH3 group of the  TEA peak by 1H nuclear magnetic resonance (NMR) using an AVANCE III 400 MHz  (Bruker). After the ion exchange, the solution was removed using a rotary evaporator and  dried under vacuum to obtain ASPI-Li. The molecular weight was determined by gel  permeation chromatography using an LC-2000Plus (JASCO Corporation). The eluentPage 9 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60was a 0.121 mol/L NaNO3 and 0.300 mol/L water: N,N’-dimethylformamide (3:2 v/v)  mixed solvent, and the molecular weight was calculated based on the standard calibration  curve created using standard poly(styrene sulfonic acid) sodium salt. The internal  structure of each polyimide thin film was evaluated using polarizing optical microscopy  (POM). Measurements were performed using a BX51-P microscope (Olympus) and a  DP28 camera (Olympus). The data were recorded using the cellSens Controller software.  The synthesized polyimides were identified using Fourier-transform infrared  spectroscopy with attenuated total reflectance (ATR-FTIR). The measurements were  performed using a Nicolet 6700 spectrometer (Thermo Fisher Scientific), and OMNIC  software (Thermo Fisher Scientific) was used for the analysis. The obtained spectra were  corrected for distortion using the advanced ATR correction feature in OMNIC.Preparation of NCM523@ASPI-Li core–shell particlesNCM523 (5E12D, Housen Co. Ltd., Japan) powders were dispersed in a solution of ASPI  in aqueous tetrahydrofuran (THF) (0.5 wt% in 1:1 THF:water) and then mixed in a  planetary centrifugal conditioning mixer (ARM-310, THINKY Inc.) for 12 min and 30 s.  The weight ratio of ASPI-Li to NCM523 was controlled at 1:99 by weight. The mixed  solution was then vacuum-filtered using a polytetrafluoroethylene (PTFE) membrane  filter (= 0.10 m). The filtrate was then dried at 80 ˚C for 24 h in a vacuum oven.Page 10 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Structural and electrochemical characterizationField-emission scanning electron microscopy (FE-SEM, JCM-5700, JEOL Ltd., Japan)  was performed at an acceleration voltage of 2 kV to study the morphology of the pristine  and polymer-electrolyte-coated NCM523 powders. High-magnification images were  obtained using a transmission electron microscope (TEM; JEM-ARM200F, JEOL). The  sample was coated with Os to prevent damage to the Ga ion beam during sample  preparation. The TEM holder was airtight and the observations were conducted at room  temperature. The electron acceleration voltage was set at 200 kV. Elemental and chemical  analyses were performed using electron energy loss spectroscopy (EELS) and  transmission electron microscopy (TEM). The chemical states of the NCM523 powder  and electrode surfaces were performed by X-ray photoelectron spectroscopy (XPS; JPS- 9200, JEOL Ltd., Japan) equipped with a monochromatic Mg Kα (1253.6 eV) X-ray  source at acceleration tension and intensity of 10 kV and 10 mA, respectively. The  organised structure of the ASPI-Li thin film before and after adding a 1:2 (v/v) mixed  solvent of ethylene carbonate (EC): dimethyl carbonate (DMC), (EC-DMC), was  measured using in situ grazing-incident small-angle X-ray scattering (GIXRS). GIXRS  measurements were performed using a NANOPIX instrument (Rigaku Corporation,  Japan) equipped with HyPix-6000HE. A Cu Kα line (MicroMAX-007HF) was used as aPage 11 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60beam source, which was further focused and collimated with a confocal multilayer mirror.  The sample was placed in a homemade relative humidity (RH)-controllable chamber. The  RH was controlled to 5–6% by flowing dry N2 gas using a precise humidity control  generator (Micro Equipment Inc., Tokyo, Japan) at room temperature. The collimated X- ray beam was directed at the sample with an incident angle of 0.19°. The camera length  was set to 140 mm, and the direct beam was blocked using a beam stopper. An ASPI-Li  thin film was fabricated on a glass substrate by spin coating using an Active Spin Coater  ACT-220D (Active). ASPI-Li was dissolved in a mixed solvent of deionised water:  tetrahydrofuran = 1:1. The polymer concentration of the solution was optimised to obtain  a film thickness of approximately 500 nm.The ion conductivity of ASPI-Li thin films parallel to the substrate was measured using  the alternating current (AC) impedance method. ASPI-Li was spin-coated to Au  interdigitated electrodes (IDE), where the gap between the electrodes was 15 μm and the  full length of the IDE was 21.8 cm. The impedance of the thin films was measured using  a 1260 Impedance/gain-phase analyser (Solartron Analytical), an amplifier 1296  Dielectric interface (Solartron Analytical). An AC voltage of 50 mV was applied, and the  impedance was measured while scanning frequencies from 1 Hz to 1 MHz. The ionicPage 12 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60conductivity was measured under a continuous flow of dry N2 gas (\~5% RH) before and  after the addition of EC-DMC to the surface of ASPI-Li.Neutron reflectometry (NR) measurements were performed at BL16 SOFIA (SOFIA) and  BL17 (SHARAKU)34, which are horizontal- and vertical-type time-of-flight neutron  reflectometer, respectively, located in in Japan Proton Accelerator Research Complex,  Material and Life Science Experimental Facility (J-PARC MLF, Ibaraki, Japan). Neutron  pulses of 25 Hz were generated with a wavelength λ band of 0.2–0.88 nm. Reflectivity  profiles were recorded at reflection angles of 0.3, 0.7, 1.6, and 3.5° to obtain a q-range of  0.07–3.1 nm–1. Here, q is the magnitude of the scattering vector defined by q = 4πsinθ/λ,  where θ is the incident angle. The NR profiles were analysed using the MOTOFIT35,  IGOR PRO software package to obtain the scattering length density (SLD) profile along  the film thickness direction. The ultrathin ASPI-Li thin film was prepared on the 50.8  mmφ CaF2 (Pier Optics Co., Ltd.) substrate by spin-coating.The electrochemical performance of the NCM523 electrodes was investigated using  R2032 coin-type half cells. The electrodes were prepared in a dry room with dew point  of less than -40 °C. The electrode slurries were composed of a 94% (w/w) active material  (NCM523 or ASPI-H coated or ASPI-Li coated NCM523), 3% acetylene black (DenkaPage 13 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Chemical Industry Ltd., Japan), and 3% polyvinylidene fluoride (Kishida Chemical Co.,  Ltd., Japan). N-methyl-2-pyrrolidone (Kishida Chemical Co. Ltd., Japan) was used as the  solvent for slurry preparation. After mixing these materials in a conditioning mixer (AR- 300, THINKY Inc., Japan), the slurry was applied onto Al foil current collectors using a  baker type adjustable film applicator (PI-1210, Hosen Ltd., Japan), followed by vacuum- drying at 120 °C overnight. After they were dried, the cathodes were cut into 14 mm  circular shapes with a hand punch and pressed at 50 kN using a hydraulic press (P-1B,  RIKEN KIKI Ltd., Japan). A solution of 1M LiPF6 in ethylene carbonate: dimethyl  carbonate (EC:DMC 1:2 v/v) was used with polypropylene (Celgard #2400) as separators.  A potentio-galvanostat (VSP-300, Biologic, France) was used to measure the EIS of the  half cells with 50% and 100% state of charge (SOC) within the frequency range of 200  kHz to 1.00 mHz with temperature variation. Constant current charge-discharge tests  were performed with a potentiostat (HJ-SD8 series, Hokuto Denko Ltd., Japan) at a  current density of 0.2–10C within the cutoff voltage range of 2.8–4.3 V. Galvanostatic  intermittent titration technique (GITT) was performed with a batter testing system  (Neware BTS-4008) to evaluate the Li diffusion coefficient in both bare and polymer  coated NCM523 containing half-cells.  The test was carried out at a constant current  pulse of 0.05C for 10 min, followed by a rest for 30-min, within the voltage range of 3.5–Page 14 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 604\.2V. Prior to all electrochemical experiments, the coin cells were cycled at a constant  current (CC mode) at 0.2C rate for three cycles to induce the formation of CEIs.Single particle galvanostatic testsA Pt microwire 10 m in diameter was sealed in a glass capillary.36 The tip of the glass- sealed Pt microwire was cut to yield a microdisk and then polished carefully to a mirror  face. The single-particle measurement system was operated in a super dry room. The  microelectrode was manipulated using a micromanipulator (QP-2RH, MicroSupport) to  contact the probe with the single-stranded NCM523@ASPI-Li core–shell particle under  an optical microscope (BX-51, Olympus). The electrolyte was composed of EC and  propylene carbonate (PC) (1:1, v/v) containing 1 M LiPF6 (Kishida Chemical Co., Ltd.).  The counter electrode was a Li foil supplied by Honjo Metal Co., Ltd., and  electrochemical measurements were performed using a two-electrode system. The  galvanostatic charging and discharging tests were carried out with an electrochemical  analyser (SP-200, BioLogic) in the range 3.0–4.2 V vs. Li/Li+. The ambient room  temperature was maintained at 295 K.LiCoO2 thin film depositionPage 15 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60(001)-oriented LiCoO2 epitaxial thin film of thickness 60 nm were deposited on (0001)- oriented Al2O3 single crystal substrate (15 × 15 × 0.5t mm, SHINKOSHA CO., Ltd.).37 A  Li-rich target, Li1.2CoO2, was used to compensate for the loss of Li during deposition. A  KrF excimer laser (wavelength of 248 nm) was used to irradiate the target at a repetition  rate of 5 Hz. The target fluence was 1.0 J/cm2. During the deposition process, the partial  pressure of oxygen was 1 × 10−6 Torr, and the substrate was kept at room temperature.Results and DiscussionATR-FTIR Characterisation of ASPI-Li filmsFigure 1(a) shows the molecular structure of ASPI-Li. ASPI-Li was prepared using an  ion-exchange reaction between a tetraethylammonium cation and a Li cation. 1H NMR  spectrum of ASPI-Li (Figure S2) suggests a 98.8% ion exchange rate from TEA to Li+  ions. Furthermore, the absence of -COO− or -NH vibration modes in the ATR-FTIR  spectra of both ASPI-TEA and ASPI-Li suggested that the ring-opening of polyimide  moieties was negligibly small (Figure S3). The weight-averaged molecular weight and  polymer dispersity of ASPI-Li were 2.1×105 and 3.5, respectively.Page 16 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60\<Figure 1\>Characterisation of organised structures in ASPI-Li thin filmThe nature of the lyotropic liquid crystals was investigated by conducting POM  observations on the ASPI-Li thin films (Figure 1(b)). A clear birefringence pattern was  observed with a domain size of ca. 50 μm, indicative of the liquid crystalline nature.  Furthermore, the structure of ASPI-Li under the operating conditions of a Li-ion battery  was examined using GIXRS. Figures 1(c) and (d) show the changes in two-dimensional  GIXRS images of 500 nm thick ASPI-2-Li thin films after adding EC-DMC. Addition of  the EC-DMC solution provided a scattering signature in the out-of-plane direction near  the specular region. The corresponding one-dimensional out-of-plane profiles are shown  in Figure 1(e). The scattering peaks at q1 = 1.19 nm−1 (5.29 nm) and its higher order  scatterings (2q1 and 4q1) can be assigned to the self-organised structure of ASPI-Li. In  contrast, the scattering signals assigned to the polymer unit length disappeared completely  (Figure 1(f)). ATR-FTIR spectroscopy was also performed (Figure S4). The presence of  the C=O vibration mode of EC-DMC centred at 1780 cm-1 suggests the incorporation of  EC-DMC molecules into the ASPI-Li structure. The 3.1±0.2 molecules per -SO3LiPage 17 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60functional group were incorporated into ASPI-Li structures, as quantified by the weight  change of the ASPI-Li thin film after the EC-DMC addition.The scattering peaks observed in the GIXRS could be attributed to the layered periodic  structure formed in the ASPI-Li thin film by the incorporation of EC-DMC molecules  because the formation of the periodic structure was observed only in the out-of-plane  direction. Thus, the scattering can be reasonably attributed to the lamellar structure  stabilised by the phase separation of the lithium alkyl sulfonate layer of the side chain and  the polyimide layer of the main chain. The scattering of ASPI-Li upon EC-DMC addition  was also observed on (001)-oriented LiCoO2 thin film prepared by RF magnetron  sputtering (Figure S5). LiCoO2 is an analogous transition metal layered compound to  NCM523. This strongly supports the possibility that ASPI-Li ultrathin films deposited on  the surface of NCM523 particles form similarly organised nanostructures with the  assistance of lyotropic liquid crystals.The Li-ion conductivity of the lamellar-structured ASPI-Li thin films was evaluated using  AC impedance spectroscopy. Figure 1(g) shows typical Nyquist plots of the dried state  and EC-DMC-incorporated ASPI-Li thin films. Although no lithium salt, such as LiPF6,  was added, the incorporation of EC-DMC molecules enhanced the Li-ion conductivity ofPage 18 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 601\.2×10-12 S·cm-1 to 1.3×10-8 S·cm-1 . The lithium ions of the alkyl sulfonate side chains  contribute to Li-ion diffusion in the lamellar layer. Furthermore, the ion conductivity of  the ASPI-Li thin film in 1 M LiPF6/EC-DMC solution was comparable to that in EC- DMC without Li salt (Figure S6). This suggested that LiPF₆ was not incorporated into the  organized structure of ASPI-Li.\<Figure 2\>Structural characterisation of NCM523@ASPI-LiThe morphological changes in the NCM523 particles after ASPI-Li thin-film  coating were investigated by FE-SEM (Figures 2(a) and (b)) at different  magnifications. The morphology of pristine NCM523 was preserved after coating.  However, the lack of a noticeable difference between the images of the coated and  uncoated materials results from the formation of an ultrathin homogeneous  polymer layer with no cracks or agglomerates which is undetectable at the  resolution of the FE-SEM instrument used for this study. Scanning transmission  electron microscope (STEM) combined with electron energy loss spectroscopy  (EELS) was used to further investigate the polymer coating layer. The defocusPage 19 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60technique was utilized for the STEM-EELS line analysis for preventing electron  beam damage. Figures 2(c) show the line analysis and corresponding heat-map  images to visualize peak position and intensity) for C in EELS (\~285 eV) with a  pitch of 1 nm in the upper 50 nm region from the polar surface to the inner core.  The spectra attributed to the NCM523 phase and the protective Os layer were not  clearly observed, however signals from the C-containing material were clearly  detected. This suggests that an ASPI-Li polymer layer is formed on the surface of  NCM523 particles. It is considered that the thin layer with different contrast on the  NCM523 surface observed in the STEM image corresponds to the ASPI-Li layer,  and the thickness of the overlayer is estimated to be 30 nm. Figure 2(d) shows a  TEM image indicating the presence of an inhomogeneous coating thickness of 17– 60 nm with an increase in the polymer content of the particles from 0.25% to 1%.  The XPS core-level spectra of the pristine and ASPI-Li-modified powders (Table  S1) also suggest the formation of a coating layer on the surface-modified NCM523  in the presence of a small percentage of sulphur and increased Li content, which is  expected to originate from the structure of the ASPI-Li polymers. To gain insight  into the formation of the organized structure in ultrathin ASPI-Li induced by EC- DMC, neutron reflectometry (NR) was conducted on both pristine and EC-DMC-Page 20 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60treated samples (Figure S7). After adding EC-DMC and drying the 15 nm ASPI- Li film, a scattering peak at 1.12 nm⁻¹ was observed, close to that in the 500 nm- thick ASPI-Li film (Figure 2e). The reflectivity profiles were fitted using a two- layer model for the pristine ASPI-Li, whereas the EC-DMC-treated ASPI-Li  required a model incorporating three periodic stackings of polymer and EC-DMC  layers. Parameters used for NR profile analysis are summarized in Figure S7. An  expansion in the total film thickness was observed upon EC-DMC treatment, and  the amount of EC-DMC incorporated was estimated from the SLD to be  approximately one EC-DMC molecule per SO3Li group. These results indicate the  formation of an organized structure in ultrathin ASPI-Li films, supporting the  potential of ASPI-Li as a CEI material in Li-ion batteries.\<Figure 3\>Electrochemical characterisation of NCM523@ASPI-LiFigure 3(a) shows the typical galvanostatic charge–discharge profiles of the half-cells  containg a solution of 1M LiPF6 in EC:DMC 1:2 v/v as an electrolyte. Evidently, the  presence of the coating slightly increased discharge capacity (172 mAh·g-1) compared toPage 21 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60NCM523 (166 mAh·g-1) at a relatively slow discharge rate of 0.2 C. This contribution is  considered to arise from the increased Li-ion conductivity of the ASPI-Li film itself,  which occurs throught the incorporation of EC-DMC molecule in the organized lamellar  structure.The increse of the specific capacity by the presence of the ASPI-Li layer is obviously  enhanced under the higher discharge rate conditions. Figure 3(b) shows the discharge  curves at various rates ranging from 0.5C to 10C, with all charge processes performed  under controlled conditions in the constant current constant voltage (cccv) mode at a  constant C-rate. Compared to that observed at 0.5C, the working voltage for the solid- solution redox reaction assigned to Co4+ → Co3+ and Ni4+ → Ni3+ decreased at higher  discharge C-rates in all cells, which was ascribed to the growth of internal resistance with  increasing current density. The voltage drop was attenuated in comparison with that of  the bare NCM523 electrode, which confirms that the ASPI-Li layer mitigated the growth  of the internal resistance with increasing current density. Variations in the discharge  capacities and capacity retention percentages with the number of cycles are summarised  in Figure 3(c). The NCM523 and NCM523@ASPI-Li cathodes underwent significant  capacity degradation with increasing C-rates. The specific capacity and working voltage  also decreased significantly with increasing C-rates. This suggests that the growth of thePage 22 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60internal resistance, due to the Li+ diffusion limit to the electrode surface from the bulk  electrolyte with increasing current density, became tangible at a rate \>4C. Notably, the  effect of the ASPI-Li coating was recognisable in discharge rates between 3C to 8C. The  effect of the ASPI-Li coating on capacity retention was most pronounced at a discharge  rate of 4C, with the NCM523@ASPI-Li electrode showing a capacity retention gap of  \~30% compared to the NCM523 electrode. This indicates that the ASPI-Li coating clearly  contributes to the improved C-rate capability in the discharge process and can sufficiently  mitigate capacity degradation at rates of up to 8C. Li-ion conductive ASPI-Li layer  functions as an artificial CEI layer is expected to provide accelerated Li ion diffusion in  the ion conductive channel by the incorporation of EC-DMC molecules. Furthermore,  additional movable lithium ions of the alkyl sulfonate side chains in the lamellar layer  will also contribute to Li-ion diffusion at the interface which results in the enhancement  of C rate capability. The impact of the ASPI-Li coating completely vanished when the test  was performed at \>9C, suggesting that the effect of the ASPI-Li layer reached its limit  under these conditions and that the rate-determining step shifted from Li+ exchange or  desolvation at the electrode interface to Li+ mass transfer in the electrolyte.Cao et al. designed a surface-modified NCM811 with a conductive polyaniline- polyethylene glycol (PANI-PEG) coating which could achieve improved ratePage 23 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60performance owing to the high electrical conductivity of PANI and the capability of PEG  chains to form accessible diffusion pathways for Li ions.38 In the case of NCM523@  ASPI-Li systems, the ordered liquid crystalline nature of the polymer electrolyte creates  liquid–fluidic ionic channels on the electrode surface that facilitate Li diffusion, which in  turn increases the local Li-ion concentration in the vicinity of the cathode surface.The intrinsic discharge characteristics of NCM523@ASPI-Li were evaluated by  performing a discharge rate performance test using a single-particle measurement  technique, in which a lab-made Pt microprobe was used to make an electrical connection  with one active material particle.36 Using this technique, we can ascertain the inherent  electrochemical properties of the cathode materials. This does not account for the  influence of the components and properties of the electrode slurry, for example, the effect  of interaction with conductive carbon, binding polymers, and the effect of cathode  thickness and density. Figure 3(d) shows the galvanostatic charge–discharge profiles with  a charging current of 2 nA and a discharging current of 50 nA. This demonstrates that  ASPI-Li coating decreases overvoltage for the discharging reaction by 0.2 V (vs. Li/Li+).  The improvement in the interface kinetics offer a better rate performance for a single  particle (Figure 3(e)). This is in agreement with the C-rate performance tests conducted  for half cells with bare and ASPI-Li-coated composite electrode systems. These resultsPage 24 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60imply that the ASPI-Li coating can intrinsically enhance the electrochemical performance  of the active materials, irrespective of the chemical and physical structures of the  electrode composites.\<Figure 4\>Figure 4(a) shows the Nyquist plot obtained from the EIS measurements of the  NCM523 and NCM523@ASPI-Li cathodes based on half cells, to gain further  insight into the effect of the ASPI-Li coating on the internal resistances. Prior to  EIS measurements, the coin cells were subjected to aging (cycling at 0.2C for three  cycles) followed by cycling at gradually increasing C-rates from 0.5C to 5C as  shown earlier in the rate performance test (Figure 3(c)), followed by charging to  50% SOC. The semicircles obtained from the Nyquist plots were fitted to the  equivalent circuit model in EC-Lab software (Figure 4(b)), using the corresponding  Bode plots (Figure 4(c) and 4(d)). The semicircle in the Nyquist plot comprises an  overlap of two separate semicircles corresponding to the resistive components RCEI  and RCT originating from the resistance at the CEI layer and the charge-transfer  resistances, respectively. The values of these resistive elements, calculated from  the equivalent circuit models, are shown in Figure 4(b). The ASPI-Li coatingPage 25 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60reduced the total resistance and those of both the resistive elements. The significant  reduction of CEI resistance can be attributed to either ASPI-Li layer with higher  Li-ion conductivity as an artificial CEI formation enable Li-ion transfer with less  resistance. Electronegative oxygen in the artificial CEI layer made of ASPI-Li thin  film can attract Li ions from the electrolyte, thereby facilitating Li-ion conduction,  which ultimately results in lower resistance at the CEI.The lower RCT for the ASPI-Li-coated systems also suggests that there is an  effective interaction between the Li ions and the CEI layer. Charles-Blin et al.  previously showed a similar reduction of RCT in Li2B4O7 coated LiCoO2 electrodes,  which was correlated with lower activation energy for Li-ion diffusion and an  increase in the local concentration of Li-ions obtained from the analysis of  capacitive components in EIS.23 Similarly, in the NCM523@ASPI-Li system, a  reduced RCT originated from easily accessible Li-ion diffusion pathways provided  by the ordered ionic channel in the ASPI-Li layer. It is considered that the ASPI- Li layer offers lowered activation energy for the desolvation of Li-ion coordinated  with the alkyl sulfonate side chains in the lamellar layer and provides the enhanced  local Li-ion concentration, as opposed to that of the carbonates based liquid  electrolyte.Page 26 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60To gain a deeper understanding of the internal resistances at the electrode surfaces, we  measured the activation energies of the resistance components by performing EIS  measurements from 40 °C to 0 °C in 10 °C intervals at a controlled SOC of 50%. The  resistances at each temperature, extracted from the equivalent circuit model, were fitted  to the Arrhenius equation, and the activation energies of the individual components were  calculated following the method reported by Nakayama et al.39 Figures 4(e) and 4(f) show  the temperature-dependent impedance spectra, and Figure 4(g) presents the  corresponding Arrhenius plots. The resistance values at each temperature are summarized  in the table in Figure 4(h).In the Arrhenius plots, the resistance components generally exhibited linear temperature  dependence, indicating thermally activated behavior. One data point deviated slightly  from the linear trend, which we attribute to possible experimental error or localized  variations in interfacial properties at that specific temperature. Nevertheless, the  activation energies were determined from the predominant linear region, and this minor  deviation does not affect the overall conclusions of the analysis.The cathode-electrolyte interface resistance RCEI was slightly more sensitive to  temperature variations than RCT for both bare NCM523 and NCM523@ASPI-Li. The  activation energy of RCEI was significantly lower for NCM523@ASPI-Li compared toPage 27 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60bare NCM523, while the activation energy of RCT was slightly reduced by the ASPI-Li  coating. The increase in impedance below 20 °C can be explained by the freezing of the  segmental motion of the polymer chains in the solid electrolyte coating, which inhibits  Li-ion conduction. However, the RCT of the coated materials remained lower than that of  the uncoated materials across the entire temperature range.The activation energy reported for Li-ion solvation by open-chain carbonates is typically  \~0.70 eV.40-42 This suggests that the ASPI-Li coating slightly lowers the activation energy,  thereby accelerating the desolvation reaction within the electric double layer formed at  the electrode interface. Although the exact mechanism of ion transport enhancement in  the NCM523@ASPI-Li system remains unclear, one possible explanation is that charge  transfer is still facilitated despite the frozen segmental motion. This may arise from the  decoupling of ion diffusion from the structural relaxation of the polymer segments, a  phenomenon commonly observed in superionic systems.43-45 These results suggest that  the activation energy for lithium-ion desolvation in the lamellar layer becomes lower than  that in the bulk electrolyte.GITT was used to obtain information on the effect of the ASPI-Li coating on the diffusion  of Li ions. The following equation was used to calculate the Li diffusion co-efficient  during discharging.46Page 28 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60太字斜体 大文字 D 下付き 、 上付き文字 てい , 太字斜体 大文字 L 太字斜体 i. , 最後 てい , じょう プラス 、 最後 下付き文字 イコール 太字 4 割る 太字斜体 パイ 太字斜体 タウ 、 始めかっこ 分子 、 太字斜体 m 太字斜体 大文字 V 下付き 太字斜体 大文字 M 最後 分子 , 割る 太字斜体 大文字 M 太字斜体 大文字 A. , 終わりかっこ じょう 太字 2 、 始めかっこ 分子 、 増分 太字斜体 大文字 E 下付き 太字斜体 大文字 S 最後 分子 , 割る ぶんぼ 、 増分 太字斜体 大文字 E 下付き 太字斜体 タウ 、 最後 ぶんぼ , , 終わりかっこ じょう 太字 2 𝑫𝑳𝒊+ = 𝟒𝝅𝝉 ( 𝒎𝑽𝑴 𝑴𝑨) 𝟐( ∆𝑬𝑺 ∆𝑬𝝉) 𝟐Here, VM is the molar volume, M is the molar mass, m is the mass of the active  material, and A is the electrode surface area. Figure S7 shows the diffusion  coefficients for the discharge process as a function of voltage calculated from the  GITT discharge curves. Li diffusion coefficients for NCM523 and  NCM523@ASPI-Li coated half cells rise from 10-11 cm2 s-1 to 10-8 cm2 s-1, before  plateauing around 3.7 V without significant changes. Although the C-rate test  implied enhanced Li-ion transport kinetics due to the ASPI-Li coating, the GITT  measurements could not detect any noticeable changes. This suggests the presence  of a third layer between NCM523 and the ASPI-Li interface. The authors believe  that this may be an EC-DMC with a LiPF6 electrolyte (slower desolvation step) or  an ASPI layer with a disordered layered lamellar structure formation at the extreme  surface of NCM523 (degrading Li-ion diffusion kinetics, as compared to that in  the ordered lamellar structure). This was supported by the relatively broad and  weak scattering in the OP scattering in LCO (Figure S5) compared with that in  glass substrate (Figure 1(e).\<Figures 5\>Page 29 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60XPS was conducted to understand the chemical states of the extrema surfaces of the  NCM523@ASPI-Li electrode. Figures 5(a) and 5(b) show the XPS O1s core-level spectra  of the NCM523 and NCM523@ASPI-Li cathodes surface, respectively, after aging for  three cycles. The O1s spectra could be deconvoluted into four bands based on several  components of the cathode materials, ASPI-Li, and the CEI layer from the reaction with  the EC-DMC/LiPF6 electrolyte. The spectra included spectra centred at 529.3 eV  (transition metal oxide M-O bond), at 530.9 eV (Li2CO3 and LiOH), at 532.6 eV (C-O  and C=O from organic decomposition products like RCH2OCOOLi and ASPI-Li), and  534.0 eV (attributed to LixPOyFz). 47-49 Compared with that in the O1s spectra of NCM523  and ASPI-Li coated NCM523, the band arising from inorganic decomposition products  Li2CO3 and LiOH becomes smaller in the coated cathodes. The reduction of Li2CO3 and  LiOH which are known to have insulating properties causing capacity degradation, can  be assumed to contribute to the improved electrochemical performance of the polymer  electrolyte-coated cathode.11 Moreover, the components corresponding to C-O and C=O  also increase noticeably in the ASPI-Li coated system which may arise from the structure  of the polymer itself. These oxygen sites can be assumed to bond with Li ions in the  electrolyte, resulting in improved diffusion kinetics. Figures 5(c) and 5(d) display thePage 30 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Li1s and F1s spectra, showing the presence of LiF (56.2 eV in Li1s, 684.8 eV in F1s  spectra) along with LiPF6 and LixPOyFz (687.4 eV and 685.4 eV, respectively). For bare  NCM523, the spectra attributed to Li1s were not detected. The abundance of Li on the  surface of the NCM523@ASPI-Li cathode suggests that the ASPI-Li layer stores Li ions  in the nanochannel (sufficient for detection by XPS). The Li-rich artificial CEI layer  exhibited increased ion conductivity and kinetics for the charge-transfer reaction at the  interface.ConclusionElectrochemical analysis using coin-type half cells was performed to demonstrate the  effects of ASPI-Li coating on NCM523 particles, as a functional artificial CEI layer, on  the properties of the corresponding electrodes, particularly from the perspective of  kinetics. The amphiphilic ASPI unit exhibited a lyotropic liquid crystal nature through a  reserved 1M LiPF6 salt containing the EC-DMC electrolyte, offering liquid–fluid lamellar  ionic-conductive highways to the NCM523 cathode-based lithium-ion battery system.  EIS analysis of the NCM523@ASPI-Li electrodes at designated SOCs revealed that the  ASPI-Li layer accelerated charge transfer, which is typically limited by the desolvationPage 31 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60of Li ions by open-chain carbonates at the electrolyte interface. Furthermore, the  calculated activation energies strongly suggested that Li+ transfer within the ASPI-Li  required less energy than the desolvation mechanism that would occur on the bare  NCM523 cathode. Although the diffusion-controlled step accompanied by desolvation is  widely accepted as the rate-determining process in battery reactions, our results suggest  that the ASPI-Li lyotropic liquid-crystal electrolyte coating increases the local Li+  concentration and ion diffusion kinetics on the NCM523 particle surface. This shifts the  rate-determining step to the reaction-controlled process. Our report is the first to provide  a complete picture of the effects of coating the surface of cathode active material particles  with a highly organised polymeric electrolyte composed of nanostructured ionic channels.  These promising results reveal new possibilities for exploiting lyotropic liquid crystalline  conductive polymers with diverse structures as artificial CEI layer materials, with the aim  of enhancing the electrochemical performance in terms of kinetics.AUTHOR INFORMATIONCorresponding Author\*E-mail: zettsu@shinshu-u.ac.jpAuthor ContributionsPage 32 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60N. Z. conceived the study. M. M., K. A, A. S, S. I, and Y. N. designed and performed the  synthesis and structural characterization of ASPI-Li (K. A., A. S., S. I., and Y. N.), the  preparation and electrochemical characterization experiments of NCM523@ASPI-Li (M.  M., and M. N.), GI-SAXS (K. A., M. H., and S. N.), NR (K. A., K. Y., Y. N., T. M., H. A.)  and single particle measurement (K. N.) and LiCoO2 thin film deposition (S. K., T. S.,  and T. H.). N. Z., M. M., K. A., and Y. N. wrote the manuscript.ACKNOWLEDGMENTThe authors would like to acknowledge Mr. Munenori Uno, Machine Shop in Center for  Nano Materials and Technology, JAIST, for the fabrication of the humidity control  chamber for GIXRS. Neutron reflectivity measurements were performed at BL16 and  BL17 at the Material and Life Science Experimental Facility, J-PARC, Japan. This study  was partially supported by JST-CREST (JPMJCR21B3, JPMJCR22O4), JSPS  KAKENHI Grant Number 24H02203, 24K17611, and 24K01154. Neutron reflectivity  measurements were performed at BL16 (2023A0162, 2024A0066) and BL17 (2018B010)  at the Material and Life Science Experimental Facility, J-PARC, Japan.Page 33 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60REFERENCES1 J. B. Goodenough and K.-S. Park, J. Am. Chem. Soc, 2013, 135, 1167–1176.2 A. Manthiram, Nat. Commun, 2020, 11, 15503 M. Weiss, R. Ruess, J. Kasnatscheew, Y. Levartovsky, N. R. Levy, P. Minnmann,  L. Stolz, T. Waldmann, M. Wohlfahrt-Mehrens, D. Aurbach, M. Winter, Y. Ein-Eli  and J. Janek, Adv Energy Mater, 2021, 11, 2101126.4 T. Abe, H. Fukuda, Y. Iriyama and Z. Ogumi, J. Electrochem. Soc., 2004, 151,  A1120.5 T. Abe, F. Sagane, M. Ohtsuka, Y. Iriyama and Z. Ogumi, J. Electrochem. Soc.,  2005, 152, A2151.6 T. R. Jow, S. A. Delp, J. L. Allen, J.-P. Jones and M. C. Smart, J. Electrochem. Soc.,  2018, 165, A361–A367.7 S.-T. Myung, K.-S. Lee, D.-W. Kim, B. Scrosati and Y.-K. Sun, Energy EnvironPage 34 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Sci, 2011, 4, 935–939.8 H.-J. Noh, Z. Chen, C. S. Yoon, J. Lu, K. Amine and Y.-K. Sun, Chem. Mater.,  2013, 25, 2109–2115.9 X. Xu, L. Xiang, L. Wang, J. Jian, C. Du, X. He, H. Huo, X. Cheng and G. Yin, J  Mater Chem A, 2019, 7, 7728–7735.10 S. Wang, A. Dai, Y. Cao, H. Yang, A. Khalil, J. Lu, H. Li and X. Ai, J Mater Chem  A, 2021, 9, 11623–11631.11 Z. Ye, L. Qiu, W. Yang, Z. Wu, Y. Liu, G. Wang, Y. Song, B. Zhong and X. Guo,  Chemistry - A European Journal, 2021, 27, 4249–4269.12 Z. Chen, H. D. Nguyen, M. Zarrabeitia, H. P. Liang, D. Geiger, J. K. Kim, U. Kaiser,  S. Passerini, C. Iojoiu and D. Bresser, Adv Funct Mater, 2021, 31, 2105343.13 Z. Chen, Z. Wang, G.-T. Kim, G. Yang, H. Wang, X. Wang, Y. Huang, S. Passerini  and Z. Shen, ACS Appl Mater Interfaces, 2019, 11, 26994–27003.14 E. H. Lee, J. H. Park, J. H. Cho, S. J. Cho, D. W. Kim, H. Dan, Y. Kang and S. Y.  Lee, J Power Sources, 2013, 244, 389–394.15 D. Zuo, G. Tian, X. Li, D. Chen and K. Shu, J Alloys Compd, 2017, 706, 24–40.16 Y. Li and Y. Qi, Energy Environ Sci, 2019, 12, 1286–1295.17 J.-J. Pan, B. Chen, Y. Xie, N. Ren and T.-F. Yi, Mater Lett, 2019, 253, 136–139.Page 35 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 6018 U. Nisar, R. Amin, R. Essehli, R. A. Shakoor, R. Kahraman, D. K. Kim, M. A.  Khaleel and I. Belharouak, J Power Sources, 2018, 396, 774–781.19 Q. Wu, X. Zhang, S. Sun, N. Wan, D. Pan, Y. Bai, H. Zhu, Y.-S. Hu and S. Dai,  Nanoscale, 2015, 7, 15609–15617.20 M. Wang, X. Feng, H. Xiang, Y. Feng, C. Qin, P. Yan and Y. Yu, Small Methods,  2019, 3, 1900355.21 T. Teranishi, Y. Yoshikawa, R. Sakuma, H. Hashimoto, H. Hayashi, A. Kishimoto  and T. Fujii, Appl Phys Lett, 2014, 105, 143904.22 S. Yasuhara, S. Yasui, T. Teranishi, Y. Yoshikawa, T. Taniyama and M. Itoh,  Electrochem commun, 2019, 109, 106604.23 Y. Charles-Blin, K. Nemoto, N. Zettsu and K. Teshima, J Mater Chem A, 2020, 8,  20979–20986.24 Z. Chen, Y. Qin, K. Amine and Y. K. Sun, J Mater Chem, 2010, 20, 7606–7612.25 R. L. Kerr., S. A, Miller, R. K. Shoemaker, B. J. Elliott, D. L. Gin\*, J. Am. Chem.  Soc., 2009, 131, 15972-1597326 J. Sakuda, E. Hosono, M. Yoshio, T. Ichikawa, T. Matsumoto, H. Ohno, H. Zhou,  T. Kato, Adv. Func. Mater., 2015, 25, 120627 X. Wang, X. Xu, S. Pu, Y. Huang, W. Ren, C. Luo, L. Fu, J. Xiao, W. Zeng, L. Liu,Page 36 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60X. Li, M. Wang, H. Cao, X. Ma, J. Colloid Interf. Sci., 2025, 682, 784-794.28 X. Wang, Y. Huang, W. Ren, C. Luo, X. Xu, Y. Wang, Y. Wang, C. Zhang, Z. Zhao,  L. Liu, X. Li, M. Wang, H. Cao, Chem. Eng. J., 2024, 502, 158155.29 W. Ren, Z. Hou, L. Su, X. Gao, Y. Chu, L. Zheng, F. Lu, Chem. Eng. J., 2024, 501,  157794.30 Y. Jiang, L. Liu, Y. Liu, J. Guan, H. Wang, M. Zhang, L. Chen, Y. Cao, R. Li, Y.  Zhou, Q. Zeng, Z. Li, W. Liu, X. Li, L. Zhang, Adv. Funct., Mater., 2025, 15,  2502613.31 X. Miao, Z. Wu, W. Hu, L. Guo, C-W. Nan, Adv. Energy., Mater., 2025, 15,  250056632  Y. Ono, R. Goto, M. Hara, S. Nagano, T. Abe and Y. Nagao, Macromolecules, 2018,  51, 3351–3359.33.  Y. Nagao, T. Tanaka, Y. Ono, K. Suetsugu, M. Hara, G. Wang, S. Nagano and T.  Abe, Electrochim Acta, 2019, 300, 333–340.34.  N. L. Yamada, N. Torikai, K. Mitamura, H. Sagehashi, S. Sato, H. Seto, T. Sugita,  S. Goko, M. Furusaka, T. Oda, M. Hino, T. Fujiwara, H. Takahashi, A. Takahara,  Eur. Phys. J. Plus, 2011, 126, 108.35.  A. Nelson, J. Appl. Cryst., 2006. 39, 273-276Page 37 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 6036 K. Nishikawa, N. Zettsu, K. Teshima and K. Kanamura, Electrochemistry, 2017,  85, 72–76.37. S. Kobayashi, E. F. Aruguelles, T. Shirasawa, S. Kasamatsu, K. Shimizu, K. Nishio,  Y. Watanabe, R. Shimizu, S. Watanabe, T. Hitosugi, ACS Appl. Mater. Interface,  2022, 14, 2703.38 Y. Cao, X. Qi, K. Hu, Y. Wang, Z. Gan, Y. Li, G. Hu, Z. Peng and K. Du, ACS Appl  Mater Interfaces, 2018, 10, 18270–18280.39 M. Nakayama, H. Ikuta, Y. Uchimoto and M. Wakihara, J Phys Chem B, 2003, 107,  10603–10607.40 J. H. Cho, G. W. Lee and Y. S. Yang, Ferroelectrics, 1997, 196, 121–124.41 K. Xu, A. Von Cresce and U. Lee, Langmuir, 2010, 26, 11538–1154342 V. Bocharova and A. P. Sokolov, Macromolecules, 2020, 53, 4141–4157.43 Y. Wang, F. Fan, A. L. Agapov, X. Yu, K. Hong, J. Mays and A. P. Sokolov, Solid  State Ion, 2014, 262, 782–784.44 F. Fan, Y. Wang, T. Hong, M. F. Heres, T. Saito and A. P. Sokolov, Macromolecules,  2015, 48, 4461–4470.45 D. W. Kim, N. Zettsu, H. Shiiba, G. Sánchez-Santolino, R. Ishikawa, Y. Ikuhara  and K. Teshima, J Mater Chem A, 2020, 8, 22302–22314.Page 38 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 6046 Y. Charles-Blin, H. Todoki, N. Zettsu and K. Teshima, Mater Adv, 2021, 2, 5406– 5414.47 P. Bai, X. Ji, J. Zhang, W. Zhang, S. Hou, H. Su, M. Li, T. Deng, L. Cao, S. Liu, X.  He, Y. Xu and C. Wang, Angew. Chem. Inter. Ed., 2022, 61, e202202731.48 A. Wang, S. Kadam, H. Li, S. Shi and Y. Qi, npj Comput. Mater., 2018, 4, 1–26.Page 39 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure 1. a) Synthetic scheme of ASPI-Li. b) Polarized optical microscope (POM) images  of ASPI-Li thin films prepared on glass substrate recorded at room temperature with  various cross-nicol arrangements. c) and d) Two dimensional (2D) GIXRS images of  ASPI-2Li thin films c) initial and d) after adding EC-DMC solvent. Insets show the  enlarged view around the specular region. e) Out-of-plane projected profiles of panels c)  and d). Black and red lines denote the initial (dry state) and after EC-DMC addition,  respectively. g) (black) Nyquist plots of ASPI-Li at 298 K under dry N2 gas flow  condition (ca. 5% RH). Inset shows Nyquist plots of ASPI-Li taken after EC-DMC  incorporation.Page 40 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure 2. (a, b) FE-SEM images of (a) NCM523 (b) NCM523@ASPI-Li particles with  varying magnifications, (c) Cross-sectional STEM images of NCM523@ASPI-Li  particles and corresponding line analysis for C, evaluated by EELS spectroscopy by 1 nm  pitch. (d)Cross-sectional TEM images of NCM523@ASPI-Li particles.Page 41 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure 3(a) Galvanostatic charge-discharge profiles of half-cells at 0.2C for NCM523 and  NCM523@ASPI-Li, (b) discharge curves and (c) discharge capacities and capacity  retention, recorded at 0.2,0.5, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10 C for NCM523 and  NCM523@ASPI-Li, recorded at room temperature, (d) the galvanostatic charge- discharge profiles with 2 nA charging current and 50 nA discharging current, e) variation  of discharge capacity of the single particles with current in logarithmic scale: NCM523  and NCM523@ASPI-Li.Page 42 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure 4(a) Nyquist plots obtained from EIS measurements of internal resistances of half cells with  50% SOC for NCM523 and NCM523@ASPI-Li; (b) the equivalent circuit model and corresponding  values of the resistive elements calculated from this model in tabular form and corresponding Bode  plots with (c) variation of phase angle with frequency and (d) variation of impedance magnitude with  frequency; (e) and (f) showing Nyquist plots of NCM523 and NCM523@ASPI-Li containing half  cells at temperatures of 0, 10, 20, 30 and 40°C and (g) the corresponding Arrhenius plots of ln(1/R)  generated (h) calculated values of activation energies from the Arrhenius plots.Page 43 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure 5. XPS core-level spectra of NCM523 and NCM523@ASPI-Li cathodes; (a, b) O1s spectra  of (a) NCM523 (b) NCM523@ASPI-Li; (c) Li1s and (d) F1s spectra of NCM523@ASPI-Li cathode.  All XPS spectroscopies were conducted to the cathodes surface taken after 1st three cycles for aging  process.Page 44 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Supporting informationLyotropic Polymer Liquid Crystal Coating: Enabling  Lamellar Ionic-Conductive Highways for Superior C- Rate Performance in NCM523 CathodesMayeesha Mariuma⁑, Kentaro Aokib⁑, Katsuhiro Yamamotoc, Athchaya Suwansoontornb, Seiya  Ikutab, Mitsuo Harad, Shusaku Naganoe, Yuki Nagaob, Kei Nishikawaf, Tsukasa Miyazakig,  Hiroyuki Aokih, Shigeru Kobayashii, Tomohito Sudarei, Taro Hitosugii, and Nobuyuki Zettsu\* a, j1. a. Department of Materials Chemistry, Shinshu University, 4-17-1 Wakasato, Nagano, 380- 8553 Japan2. b. School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1  Asahidai, Nomi, Ishikawa, 923-1292, Japan3. c. Department of Life Science and Applied Chemistry, Graduate School of Engineering,  Nagoya Institute of Technology, 466-8555 Nagoya, Japan;4. d. Department of Molecular Design \& Engineering, Graduate School of Engineering,  Nagoya University, Furo-cho, Chikusa, Nagoya, Aichi 464-8603, Japan5. e. Department of Chemistry, College of Science, Rikkyo University, 3-34-1 Nishi-ikebukuro,  Toshima, Tokyo 171-8501, Japan6. f. Rechargeable Battery Materials Group, Center for Green Research on Energy and  Environmental Materials, National Institute for Materials Science 1-1 Namiki, Tsukuba,  Ibaraki 305-0044, Japan7. g. Office of Society-Academia Collaboration for Innovation, Kyoto University, Sakyou-ku,  Kyoto 606-8501, JapanPage 45 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 601. h. Materials and Life Science Division, J-PARC Center, Japan Atomic Energy Agency, 2-4  Shirakata, Tokai, Ibaraki 319-1195, Japan2. i. Department of Chemistry, The University of Tokyo, 113-0033 Tokyo, Japan3. j. Institute for Aqua-regeneration, Shinshu University, 4-17-1 Wakasato, Nagano, 380-8553  JapanFigure S1. Synthetic scheme of ASPI-Li.Figure S2. 1H NMR spectrum of (black) ASPI-TEA and (red) ASPI-Li in DMSO-d6.Page 46 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure S3. ATR-IR spectra of (black) ASPI-TEA and (red) ASPI-Li.Figure S4. ATR-IR spectra of (grey) EC-DMC, (black) ASPI-Li and (red) ASPI-Li after  dispersing in EC-DMC, then washed with acetone.Page 47 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure S5. GIXRS results of ASPI-Li thin films on ca 60 nm thick LiCoO2 layer deposited on a  sapphire substrate. a) and b) 2D GIXRS images a) before and b) after EC-DMC addition. Inset  shows the enlarged image around the specular region. Black arrow indicates the new scattering  after EC-DMC addition. c) and d) c) Out-of-plane and d) in-plane projected profiles of panels a)  and b). Black and red lines denote the before and after EC-DMC addition, respectively.Figure S6. Nyquist plots of ASPI-Li taken at 298 K under dry N2 gas flow condition (ca.  5% RH). Red and blue plots were taken after EC-DMC and 1 M LiPF₆/EC-DMC  incorporation, respectively.Page 48 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure S7. a). NR profiles of of (red) pristine ASPI-Li thin films. and (blue) the same thin film  once EC-DMC added, then dried on a CaF2 substrate. Open circles and solid lines denote the  experimental data and fitting lines, respectively. b) fitting models, c) SLD profiles and d) fitted  parameters.Page 49 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60Figure S8. Diffusion coefficients for discharge process as a function of voltage calculated from  GITT discharge curves: NCM523 (black), NCM523@ASPI-Li (red).Table S1. Atomic percentages of selected elements obtained from XPS measurements of pristine  NCM523 and 1% ASPI-2-Li coated NCM523Page 50 of 50ACS Paragon Plus EnvironmentACS Applied Energy Materials1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60